621623

Ergofix 77207-1 Manual

23
Zoom out
Zoom in
Previous page
1/44
Next page
21
• Keep your hands well away from any splits and cracks which open in the log;
these may close suddenly and crush or amputate your fingers.
• Never force the log splitter for more than 5 seconds keeping the cylinder
under pressure in the attempt to split excessively hard wood. After this time
interval, the oil under pressure is overheated and the machine could be
damaged. It is thus better to stop and rotate the log by 90° to see whether it can
be split in a different position. In any case, if you are not able to split the log, this
means that its hardness exceeds the capacity of the machine and thus that the
log should be discarded so as not ot damage the log splitter.
• Do not force the blade by pushing the log on the upper part; as this can cause
the blade to break or damage the body of the machine. Always set the log on
the guides.
• Never leave the machine unattended while it is running. If you leave the
machine, even for a short time, remove the power supply or any possible cause
of accidental start-up.
• The log splitter must never be used by an operator who is under the influence
of alcohol, drugs, medicines, or who is tired. A clear mind is essential for safety.
• Never request the assistance of another person to help you remove a jammed
log.
• Check that the electric circuit is adequately protected and that it corresponds
with the power, voltage and frequency of the motor. Check that there is a
ground connection and a regulation differential switch upstream.
• Use cables with a section of 5 x 1,5 mm². Avoid use of free and inadequately
insulated connections. Connections must be made with protected materials
suitable for outdoor use. Do not use cables over 10 metres long, as excessively
long cables or those with inadequate section can cause voltage drops that
prevent motor from developing its full power.
• Never open the pushbutton box on the motor. Should this be necessary,
contact a qualified electrician.
• Make sure that the machine and the cable never come in contact with water.
• Treat the power cable with care. Do not attempt to move the machine by pulling
the cable. Do not yank the cable to unplug it; keep the cable away from
excessive heat, oil and sharp objects.
• Never leave the machine unattended with the power supply "on". Also
disconnect the power cable when not in use, when carrying out maintenance
work, when changing attachment or moving the machine.
4. SET UP FOR OPERATION
UNPACKING: at least 2 people are required to unpack the log splitter package.
After unpacking proceed as follows:
1 Assemble the wheels and the axle.
2 Fix the switch box with 2 x screw with screw nut.
3 Mount the control levers.
4 Assemble the work table(adjustable in height)
5 Pour the supplied oil in the oil tank through the funnel with hose.
6 Check the direction of motor rotation.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ergofix 77207-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ergofix 77207-1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info