215208

Epson emp 8300 lcd projector Manual

15
Zoom out
Zoom in
Previous page
1/16
Next page
The lamp is near the end of its operating life. Replace the lamp with a new one as soon as possible.
If you continue to use the old lamp, the possibility that the lamp may break will increase.
The lamp will switch off automatically
and projection will stop.
Wait for approximately 5 minutes.
After this, check the points to the
right. (With the EMP-8300, disconnect
the power plug first.)
User's Guide "Replacing the Lamp"
If you continue using the projector and
the temperature rises again, the lamp
will switch off automatically.
Check the points to the right.
If the indicator is flashing orange
Warning
Indicator is lit or flashing green or orange
Normal
If you press the button, projection will start after warm-up is complete.
Warm-up time is approximately 40 seconds.
After warm-up is complete, the indicator will change to steady green and projection will start.
Normal operation is in progress.
Cool-down time is approximately 30 seconds.
After cool-down is complete, the projector goes into standby mode.
You cannot use the remote control or the projector's control panel during cool-down.
If the problem is not fixed, stop
using the projector and
disconnect the power plug from
the electrical outlet.
Then contact your dealer or the
nearest address provided in the
"International Warranty
Conditions" section of the
Safety Instructions/World Wide
Warranty Terms
booklet.
If the projector
is close to a
wall, move it
away from the
wall.
Clean the air
filters if they are
blocked.
lit flashing off
lit flashing off
Standby
condition
Orange
Cool-down in
progress
Orange
Warm-up in
progress
Green
Projection in
progress
Green
Internal
temperature
error
(overheating)
Red
Red
High-speed
cooling in
progress
Orange
Red
Lamp
replacement
notification
Orange
DVI-D/DVI-D
digital video cable
or DVI-D/DFP
digital video cable
(optional)
VGA-HD15/
BNC PC cable
(optional)
Computer
cable or
VGA-HD15
PC cable
(accessory or optional)
Connecting to a
computer
The [Audio] port to use is
the port that is in the same
box as the port being used
to input the video signals.
* An accessory audio cable
is not supplied with the
EMP-9300. Use a
commercially-available
audio cable instead.
RCA audio cable
(commercially-
available)
To computer's
audio output port
To computer's
audio output port
Audio cable
(accessory)
To computer's monitor
output port
(Mini D-Sub 15-pin)
To computer's monitor
output port
(DVI-D or DFP)
Connections
Be sure to turn the power for all components off before making any
of the following connections.
User's Guide
"Connecting to a Computer"
"Connecting to a Video Source"
9300E-QRG_01-14
… 15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson emp 8300 lcd projector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson emp 8300 lcd projector in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info