749195
39
Zoom out
Zoom in
Previous page
1/48
Next page
39
IP2288EN
EN
AP
Display Description Selections
available
DC - Setting of disengagement on stop during closure [mm]
Regulates the distance of the disengagement on the mechanical open-
ing stop.
00 - Disabled
99 - Maximum
NB: not active if
07
OT - Selection of type of obstacle identification
00 - Overcurrent or gate stopped
01 - Overcurrent
02 - Door stopped
NB: the obstacle identication for “door stopped” is faster but more
sensitive.
CR - Stroke estimate correction [%]
DO NOT USE (diagnostic purposes only)
SM - Selection of operating mode of device connected to terminals 1-6
00 - During the operation, the opening of the safety contact stops the movement
(with disengagement if / ).
01 - During the operation, the opening of the safety contact stops the movement
(with disengagement if / ). When the contact closes again, the opera-
tion is resumed.
02 - During the operation, opening of the safety contact stops the movement (with
disengagement if / ). When the contact closes again, an opening
operation is performed.
03 - During the closing operation, the opening of the safety contact reverses the
movement. During the opening operation, the safety device is ignored.
04 - During the opening operation, the opening of the safety contact stops the
movement (with disengagement if / ). When the contact closes again,
the opening operation is resumed. During the closing operation, the safety device
is ignored.
05 - During the closing operation, the opening of the safety contact stops and re-
verses the movement. During the opening operation, the opening of the safety con-
tact stops the movement (with disengagement if / ).
06 - During a maneuver, the opening of the safety contact stops the movement.
When the contact closes again, automatic closing is disabled.
TN - Setting of intervention temperature for the NIO electronic anti-
freeze system and automatic HS ramps [°C]
This value does not refer to the ambient temperature, but to the inter-
nal control panel temperature.
20
TH - High temperature protection enable.
If ON, the automatic reclosing time is extended when the maximum
switchboard temperature is reached. If the condition persists, all the
controls are disabled.
HS - Automatic ramp adjustment
ON - Enabled
OF - Disabled
When enabled (ON), at low ambient temperatures the start time increases
up to the maximum value and the acceleration time and diminishes to
the minimum value.
NB: for correct operation, the control panel must be exposed to the same ambi-
ent temperature as the motors.
The intervention temperature can be set with the selection .
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entrematic Ditec ION6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entrematic Ditec ION6 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info