609401
22
Zoom out
Zoom in
Previous page
1/28
Next page
22
IP1839EN • 2012-07-31
19. RADIO RECEIVER OPERATION
The control panel is equipped with a radio receiver with a frequency of 433.92 MHz.
The antenna consists of a rigid wire, 173 mm long, connected to the ANT clamp.
It is possible to increase the range of the radio by connecting the antenna of the ashing lights, or by installing
the tuned BIXAL antenna.
NOTE: to connect the external antenna to the control panel, use a coaxial cable type RG58 (max 10 m).
Check that BIXMR2 storage module is inserted on COM connector of the control panel.
Up to 200 remote controls can be stored in the BIXMR2 storage module.
WARNING: if the radio receiver on the control panel is not used, set JR4=OFF and remove the BIXMR2 storage
module.
Transmitter storage:
- press the PRG button on the radio receiver or on the control panel; the SIG LED lights up;
- make a transmission by pressing one of the desired CH buttons of the transmitter (within the range of the
radio receiver). The transmitter is now stored. During this phase, the SIG LED ashes. When the SIG LED
is again lit up, it is possible to validate another transmitter. Validate all the new transmitters by making a
transmission as indicated;
- you automatically exit the procedure 10 seconds after the last transmission, or you can press the PRG
button again (the SIG LED goes off).
Up to four CH keys of a single remote control can be stored:
- if only one (any) CH key of the remote control is stored, command 1-5 (step-by-step/opening) is carried
out;
- from two to four CH keys of a single remote control are stored, the functions matched with the CH keys
are as follows:
CH1 = command 1-5 step-by-step/opening;
CH2 = partial opening command, it causes the automation to open for about 1 m;
CH3 = command to switch on/off the courtesy light;
CH4 = stop command, equivalent to impulsive command 1-9.
Transmitter cancellation:
- keep pressed for 3 s the PRG button on the radio receiver or on the control panel, the SIG LED begins to
ash;
- to erase all the transmitters from the memory of the radio receiver keep pressed for 3 s again the PRG
button;
- to erase a single transmitter, press one of the previously stored CH keys of the transmitter to be erased;
- the cancellation is conrmed by the quick ashing of the SIG LED.
For further information see the user manual for GOL series transmitters.
If the control panel is replaced, the BIXMR2 storage module being used can be inserted in the new control panel.
WARNING: the BIXMR2 storage module must be inserted and removed with the power supply disconnected.
10 s
CH1 CH2
CH3CH4
1 2 3
SIG
PRG
COM
ANT
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entrematic Ditec GLOBE IP1839 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entrematic Ditec GLOBE IP1839 in the language / languages: English as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Entrematic Ditec GLOBE IP1839

Entrematic Ditec GLOBE IP1839 User Manual - German - 28 pages

Entrematic Ditec GLOBE IP1839 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info