609363

Entrematic Ditec CROSS3E - IP1780 Manual

14
Zoom out
Zoom in
Previous page
1/42
Next page
CROSS3E - IP1780
14
4. ELECTRICAL CONNECTIONS
The electrical connections and starting are illustrated in the
installation manual of the control panel.
ATTENTION: Connect the yellow-green ground cable to the
clamp already connected to the motor, as it is shown in the
gure.
5. CROSS3SFINSTALLATION(fig.4)
Additional photocells can be installed inside the gear motor
utilising the optional CROSS3SF kit, so as to protect the closing
movement as well as the opening movement.
Assemble a receiver (RX) or a transmitter (TX) on the brackets
supplied, as shown in the gure.
Installation of the photocells must be carried out in observance
of the standards EN12453 and EN12445.
Attention: the photocell receiver (RX) and transmitter (TX) may
also be installed at two different heights, the maximum permis-
sible difference in height being 300 mm.
6. LUXK3EINSTALLATION(fig.5)
The LUXK3 kit permits to illuminate the area around the au-
tomatic gate for a period of 3 minutes upon the appropriate
command being given.
Secure the kit by means of the three screws provided and con-
nect to control panel as shown in the gure.
To route the leads inside the control panel, cut out the plastic
sheath at the marked spot (see LUXK3E instructions).
After the connections, mount the cover.
GB
3.5 CROSS3TC installation
- Remove the cover [F] and the retaining ring [G] and slide out
the pinion [17].
- Insert the pinion [L], the spacer [J] and fasten with the
seeger [G].
- Replace the cover [F].
- Secure the chain striker bracket [E].
3.6 Chain installation
- Release the geared motor (see OPERATING INSTRUC-
TIONS) and pass the chain between pinion [L] and stop
[E] by turning the pinion manually.
With the chain supplied, the gate has a maximum stroke
of 5.7 meters.
- Open the gate and attach brackets [C] to the leaf as shown
in gure.
- Connect the chain previously installed on the geared motor
to rod [D] and attach it to bracket [C].
- Attach the chain to the other side of the gate by means of
rod [D] and bracket [C] (cut off excess chain).
Note: with the gate in complete opening and closing posi-
tion, check that the distance between the center of pinion
[L] and rod [D] shown in gure is respected.
- Finally, rmly secure the geared motor by nuts [A].
- Tighten the chain with rods [D]. Lubricate the chain and
pinion lightly after assembly.
17 G F
G
E J
L
F
min
25
L
D
min 60
C
H
90÷10050
D
E LF
yellow-green
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entrematic Ditec CROSS3E - IP1780 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entrematic Ditec CROSS3E - IP1780 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info