807572

Enduro EM203 Manual

33
Zoom out
Zoom in
Previous page
1/52
Next page
ENDURO® EM203 27 Ref: EM203-UM-TKI-0116-Rev.A.
Remember to leave a small amount of slack cable near the motors to allow for their movement when the drive
rollers are engaged.
Use the large cable ties (27) to secure the motor cables to the motor. This ensures that there is no force and
movement on the spade connectors or movement of the cables during transit.
Route the motor cables along the underside of the caravan floor, inside the supplied convoluted trunking (11)
(this will protect the electrical cables against sharp edges and dirt) and through the drilled hole.
Secure the cable trunking (11) to the chassis or under body of the caravan by using the P-Clips (20) and screws
(19).
Once the motor cables are through the drilled hole next to the control unit (32), cut the cables, ensuring that
they are same length. Remove approx. 5mm of the insulation from the ends. Fix the spade connectors (24) by
using crimping pliers. A secure and good quality connection on each cable is essential.
Attach the connectors to the terminals on the control unit (see wiring diagram Fig. 12).
Find a suitable place for the battery power isolation switch (29) which includes an external holder with hinged
cover. Important: The switch must be mounted onto the exterior body of the caravan and be easily
accessible from the outside of the caravan in case of any emergency. The switch must be mounted close
to the location of the battery in order to keep the length of the battery cables to a minimum.
Use the cardboard template to position the hole positions and the drill holes. Mount the switch and the housing
with the bolts, washers and nuts, and finally mount it on the caravan with stainless steel screws (19).
Route the positive (+) power cable (including fuse) from the battery to the battery power isolation switch (29)
and than further to the control unit (32).
The electronic connections of the battery power isolation switch (29) must be covered by the supplied rubber
isolation shells (33).
Route the negative (-) power cable directly to the control unit (32).
No cables may be routed over the control unit!
Again it is recommended to use the supplied trunking (11) to protect the cables against sharp edges. Attach the
trunking with P-clips (20) and P-clip screws (19).
Cut the cables to an appropriate length and remove approx. 5mm of the insulation from the ends. Fix the spade
connectors by using crimping pliers. Two types of battery terminal connector (22 & 23) are provided for use as
appropriate. A secure and good quality connection on each cable is essential.
Connect the battery cables (14 & 15) to the control unit (32).
Finally, connect the battery cables to the existing battery terminals (red = positive, black = negative).
Caution! Make sure that you do not reverse the Positive (+) and Negative (-) connections.
Incorrect connection (reverse polarity) will result in damage to the control unit.
Seal the 25mm hole in vehicle under body using plastic body sealant.
Finally find a suitable place for the remote control handset wall holder (34) and fix this by the supplied screws
(out of reach of children or other unauthorised people).
Installation of the caravan manoeuvring system is now complete.
OPERATION - SAFETY GUIDELINES
Practice operating the manoeuvring system in an open area before using for the first time. This is to fully
familiarise yourself with the handset / manoeuvring system operation.
Before use, always check the manoeuvring system for any damage.
When towing or moving the caravan please be aware, at all times, that ground clearance is reduced
when the manoeuvring system has been fitted.
Always ensure that children and pets are kept well out of the way during operation.
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro EM203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro EM203 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info