807572

Enduro EM203 Manual

32
Zoom out
Zoom in
Previous page
1/52
Next page
ENDURO® EM203 26 Ref: EM203-UM-TKI-0116-Rev.A.
Make sure that the main cross bar (3) and the cross actuation centre bar (4) are positioned in the middle of the
caravan (the centre of the bar is marked).
With the main assembly is loosely fitted onto the chassis, slide the whole assembly along the chassis until the
rollers are 20mm away from the surface of the centre each tyre (Fig. 10). Two 20mm spacers (30) are provided.
It is vitally important that each roller is at exactly the same distance away from the tyre.
The whole assembly must be parallel to the caravan/trailer axle.
Slide the motor units in or out of the cross bar (3) accordingly to ensure the roller will have
the maximum possible contact with the tread of the tyre. Ensure that the position of each
motor unit does not obstruct shock absorbers (if fitted) and that the plastic chain guard is
not too close to the surface of the tyre/shock absorber. The minimum clearance when the
drive units swivelled in is 10mm.
Fully tighten the four bolts (Fig. 1B) on the main cross bar (3) and the four bolts (Fig. 1C) on cross actuation
assembly (4 & 5).
Fully tighten all the nylon nuts on both clamping assemblies (Fig. 2). First tighten the diagonal placed M10x60
bolts with a 20Nm torque, and then M10x50 bolts to a 40Nm torque.
Re-check the distance of 20mm from the rollers to the tires, the position of the aluminium rollers in addition to
the surface of the tire and finally the distance between the chain cover (Fig. 8) and the tires & shock absorbers
(>10mm). The weight of the caravan must be on the wheels when doing this. If necessary, loosen the bolts and
re-adjust the position of the assembly.
Re-check that all bolts/nuts have been tightened to the correct torque!
The main mechanical components have now been installed.
INSTALLATION - ELECTRICAL/ELECTRONIC COMPONENTS
Make sure the 12V supply from the battery and any 230V electricity supply are disconnected.
Remove battery cable terminals and disconnect any external electrical power before starting work.
Find a suitable place for the electronic control unit (32), such as a storage area, under a seat or a bed. Make
sure this place is dry and close to the battery (40cm to 60cm). The electronic control unit can be mounted
vertically on a side wall or be mounted flat. When mounted vertically, the connections must point downwards to
avoid any short-circuits by objects falling into. When choosing location, ensure that the antenna can be
completely extended and cannot easily be damaged.
Fix the electronic control unit securely into position with four screws (19). Note: if the provided screws are not
of suitable length or type for the desired location/material please substitute these as appropriate.
Drill a 25mm hole through the floor of the caravan approximately 150mm centrally in front of the control unit
(32) terminals.
Caution! Take extra care to avoid any chassis members, gas pipes and electrical wires!
Route and connect the motor-cables in accordance with wiring diagram (Fig. 12) (red = positive, black =
negative).
The wiring diagram (Fig. 12 + Table. A (see below)) depicts the wiring route when installing the motor units in
front of the wheels/axle towards the ‘A’ frame. Please refer to table B (below) for fitment of the motor units to
the rear of the axle.
Table . A
FRONT OF AXLE FITTING
Motor A Positive (+) cable to terminal 4
Motor A Negative (-) cable to terminal 3
Motor B Positive (+) cable to terminal 2
Motor B Negative (-) cable to terminal 1
Table . B
REAR OF AXLE FITTING
Motor A Positive (+) cable to terminal 1
Motor A Negative (-) cable to terminal 2
Motor B Positive (+) cable to terminal 3
Motor B Negative (-) cable to terminal 4
Mark the motor cables (12 & 13) for both motor units using the cable markers (25). The cables for the left and
the right motor should have the same length. Avoid any loops.
Connect the spade connectors (24) to the motors. Please note that the red cable is connected to the terminal
under the moulded ‘+’ symbol on the weatherproof terminal cover. The motor cables are already fitted with
small coils. These coils must be positioned along the side of the motors.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro EM203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro EM203 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info