ENDURO
®
autoSteady 34
Ref: AS201AFL/BFL-UM-TKI-0419-Rev. A
The remote handset switches off:
After 3 minutes, if no button is pressed: After 2 minutes the buzzer will beep for 5 times with a repetition
after 3 minutes. Than the system switches in the “stand-by” modes.
After 6 minutes, if one of the movement buttons is permanently held down: After 5 minutes the buzzer will
beep for 5 times with a repetition after 6 minutes. Than the system switches in the “stand-by” modes.
The green LED goes off and the remote handset is in the “stand-by” modes which means that there always will
be used some current which causes the battery to go down. So always make sure the remote handset is turned
off by the slide switch.
To reactivate the remote handset, move slide switch to “Off” –O and then back to “On”-I after approximately 1
second.
Error messages via the remote handset:
Error messages of the autoSteady system will be communicated via the remote handset by the green LED (Fig.
8H), the error message LED’s (Fig. 8L, 8M & 8N) and a buzzer signal:
Green LED (Fig. 8H) off, no buzzer: remote handset is turned off and also system is not activated
Green LED (Fig. 8H) continue on, no buzzer: remote handset is turned on and system is activated and
ready to use.
Green LED (Fig. 8H) is blinking, no buzzer: no communication between handset and control unit. This could
be because of too much distance between remote handset and control unit, or the battery isolation switch
for manoeuvring system is not turned on or that there is a distortion signal disturbing the communication.
As soon as connection is good again the green LED will be continue on and the system is ready to use.
Blue battery voltage LED (Fig. 8N) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10V). Battery needs to be recharged.
Blue battery voltage LED (Fig. 8N) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
Red overload LED (Fig. 8L) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Blue 9V battery LED (Fig. 8M) is blinking, no buzzer: The internal 9V battery is near empty and needs to be
replaced.
Changing batteries in the remote handset:
When the internal battery is empty (blue LED (Fig. 8M) is blinking 2Hz), it needs to be replaced.
Open the rear cover of the remote handset (Fig. 9A).
Take out the old battery and dispose in the appropriate way.
Install a new replacement battery (Fig. 10). Make sure to use a leak proof PP3 (9Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
Close the rear cover again.
Dead and used batteries may leak and damage the remote handset! Remove the batteries if the remote
handset is not going to be used for an extended period.
How to synchronise the remote handset with a new manoeuvring system or autoSteady control unit:
The remote handset and the autoSteady control unit are synchronised with each other in the factory. If the
control unit or the remote handset is replaced, or the combine-remote handset will also be used for an ENDURO
®
caravan manoeuvring system, they must be re-synchronised as described below:
Check the installation in accordance with the installation instructions. Check that the battery is properly
connected, check the condition of the battery and that a voltage of 12 Volt is present at the control unit.
Please ensure that the battery isolation switch is on.
Press the reset button on the control unit:
o autoSteady system: Press the reset button (Fig. 11D) on the autoSteady control unit for three
seconds and then release it. The green LED (Fig. 11A) starts blinking quickly (2Hz).
o ENDURO
®
caravan manoeuvring system: Press the reset button (see user manual caravan
manoeuvring system) on the ENDURO
®
caravan manoeuvring system control unit for three seconds
and then release it. The green LED on the control unit starts blinking quickly (2Hz).
Activate the remote handset by sliding the slide switch (Fig. 8A) to “On”-I. The green LED of the remote
handset and the “UP” and “DOWN” LED’s (Fig. 8R & 8S) will illuminate continuously.
Push both the “UP” and “DOWN” buttons (Fig. 8B & 8C) on the remote handset at the same time for more
than 3 seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is
complete.
After successful synchronisation, the green LED on the control unit (Fig. 11A) and on the remote handset
(Fig. 8H) will illuminate continuously.
After pressing the reset button on the control unit, if have not any operation in more than 15 seconds, the re-
synchronization process will stop.
