722072

Enduro AS101 Manual

43
Zoom out
Zoom in
Previous page
1/48
Next page
ENDURO
®
autoSteady 36
Ref: AS101-UM-TKI-0114-Rev. A
After pressing the reset button on the control unit, if have not any operation in more than 15 seconds, the re-
synchronization process will stop.
OPERATION - ELECTRONIC CONTROL UNIT
The electronic control unit (6), which is mounted inside your caravan, is responsible for controlling the
autoSteady system.
The control unit has three LED’s, one pushbutton and one slide switch (Fig. 13):
Green LED (Fig. 13A): Power LED continuously lights up when the system is activated (by moving slide switch
of the remote control to “On”-I). If the remote control is far away from the control unit, beyond the availably
distance, this LED will start blinking.
Blue LED (Fig. 13B): Error message LED concerning caravan battery:
• Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).
Battery needs to be recharged.
• Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over
charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump).
Red LED (Fig. 13C) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection
is activated. Maybe the system has a current-shortage. Please check the whole system carefully. Wait about 60
seconds and try again.
In general all error messages will reset automatically after one minute. If this is not the case, reset the
electronics by switching off the system via the isolation switch and the remote control for at least 15 seconds
and then turning it on again.
The Reset Button (Fig. 13D): The remote control handset and the control unit are synchronised with each
other in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised
as described in chapter OPERATION - REMOTE CONTROL HANDSET: “How to synchronise the remote
handset with a new manoeuvring system or autoSteady control unit”
Jack-up force switch (Fig. 13E): The system is suitable for a big range of the caravans. To make sure that
the system is always working properly and your caravan is stable, the Current-protection can be adjusted via a
slide switch on the control unit (Fig. 13E):
L: Low current for caravans up to 1000kg
M: Normal current for caravans in the range of about 1000 – 1500kg
H: High current for caravans in the range of about 1500 – 2000kg
Different caravan chassis or floors have different situation for jack-up force. The above mentioned values are
just a rough indication. Please check what is the most convenient for your caravan so your caravan or caravan
chassis will not be damaged but still your caravan is stable.
OPERATION - GETTING STARTED
Please make sure you read the safety instructions very carefully and make sure that you
follow these guidelines!
Make sure that the battery that supplies the system is fully charged and in good condition.
Make sure that the caravan is free from the vehicle and the handbrake is on.
Before you can start using the autoSteady system, please make sure you caravan is already levelled out in all
directions. Please use the supplied tool (3) and accomplish this the usual way.
Just as the standard corner steady of your caravan can only be used for stabilising, also the
autoSteady system cannot be used for jacking up or levelling out your caravan.
Once the caravan is levelled out, you can start using the autoSteady system.
Turn on the battery power isolation switch (24).
Activate the autoSteady system by moving the slide switch to “On”-I on the remote control (Fig. 10A). The
green LED (Fig. 10H) will illuminate continuously. The system is ready for use.
During the operation of the system, the handbrake must be secured.
First check if the slide switch (Fig. 10O) is in “autoSteady” mode (Fig. 10Q).
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro AS101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro AS101 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info