67788

Emphaser ECP26NEOXT4 Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
– 11 –– 10 –
MID/WooFeR MoUntInG
Remove the factory grilles of the front door and remove the factory installed full range speakers or
mid/woofers. Depending on the car brand and type, it is sometimes unavoidable to remove the
complete doorpanels to gain full access to the speaker openings.
If this is the case, you should buy some spare plastic clips for remounting of the door panels after
your install is complete, as these clips tend to break quite easily.
Note that a tight fit of the door panels is important, since door panels with a loose fit swallow bass
energy and they may add unwanted rattling noise to the sound of your speaker system. Before you
proceed to mount the EMPHASER mid/woofers, check the available installation depth with both
front windows down.
Connect the speaker wires to the mid/woofers and route it to the location where the crossovers are
going to be located and installed. Pay close attention to the polarity imprints on the terminals and
wires when connecting the mid/woofers.
When you tighten up the screws to mount the mid/woofers in place, be sure to check for an airtight
seal and good fit of the basket rim to the mounting surface. You can now reinstall the factory plastic
grilles or the complete door panels.
X-oVeR MoUntInG
The crossovers can be mounted in almost any location inside the vehicle. Recommended places are:
Inside the door, under the carpet in front of the door angles, under the dash board etc. Just don’t
mount the crossovers in places where they may be exposed to water or moisture. Consider to find a
spot that allows you to fine tune the tweeter attenuation level, after your install is completed.
Connect the tweeter wires, the wires from the mid/woofers and the wires from the amplifier to the
crossover units. Make sure all wires are hooked up with correct polarity, i.e. electrically in phase,
which means positive (+) is connected to positive, and negative (-) to negative.
Out of phase connections, i.e. when a mid/woofer is concerned, will cause very low bass output
and a weird staging.
tWeeteR attenUatIon
The tweeter attenuation jumper is located inside the crossover on the circuit board. Four different
positions can be selected by moving the jumper to 0dB / -1dB / -2dB / -3dB positions. 0dB
will give you a loud and brilliant high frequency reproduction, while -3dB gives you a softer sound
in the treble region.
The correct attenuation must be played by ear, as you simply tune the high frequency balance to fit
your personal taste.
Attention: The jumper on each x-over PCB must be set to the same attenuation level.
ECP26NEO-XT4 Manual.indd 11 21.07.2006 13:00:40 Uhr
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emphaser ECP26NEOXT4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emphaser ECP26NEOXT4 in the language / languages: English, German as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info