67788

Emphaser ECP26NEOXT4 Manual

10
Zoom out
Zoom in
Previous page
1/16
Next page
– 11 –– 10 –
tWeeteR MoUntInG
The tweeter mounting location inside the car exhibits a direct influence on the front staging and sound
quality of the component system. Depending on the selected mounting location for your tweeters,
the front staging is going to be good or poor. Note that the tweeter level can be attenuated by a
jumper on the crossover’s pcb bord, enabling you to tailor the treble response for different places
of tweeter mounting.
Aim for a tweeter location as unobstructed and as high as possible – recommended places are the
center of the A-pillars, the window triangles or else always as much up and in front as possible.
Attention: The main radiation axis of both tweeters should cross at a virtual point in the center between
passenger and driver’s seat. A direct “on-axis” installation of the tweeters, where they aim or point at
the listener, is not recommended. The result of tweeters angled too much in direction to the listerners
is called “side-biasing” – which can only be compensated with a DSP based time-alignment.
Flat Surface Mounting
Two parts are needed for flat surface mounting. The main tweeter units and the flat aluminum
baseplates.
Mark and drill holes where you want to fix the tweeters. You can use the baseplate ring as a temp-
late. Three holes need to be drilled, one main hole for the cable routing and two small pilot holes
for fixing the base to the surface. You’ll need 2.5mm and 6mm drill bits and a power drill. After
drilling the holes, mount the flat adapter ring to the surface, using the two self tapping flathead
screws contained in the acessory set. Feed the tweeter wire through the center hole and connect the
tweeter wire to the extension wire. Place the tweeter over the adaptor ring, gently press the tweeter
down and turn it counter-clockwise, to lock it in place.
Flush Mounting
After choosing a mounting location that offers at least 17mm clearance behind the panel, you
need to pre-drill pilot holes for both tweeters. These two holes must be enlarged to 50mm diameter,
using a core drill. The cup adapter part must now be inserted into the cutout, and is fixed with the
mounting bar and two metrical M3 screws contained in the hardware set. Assemble the tweeters
by inserting the tweeter lead wire into the center hole of the adapter, then push the tweeter down
and turn it counter-clockwise, to lock it in place. Finally, attach the tweeter extension wires to the
lead wires on the backside of both tweeters.
ECP26NEO-XT4 Manual.indd 10 21.07.2006 13:00:40 Uhr
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emphaser ECP26NEOXT4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emphaser ECP26NEOXT4 in the language / languages: English, German as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info