168847
9
Zoom out
Zoom in
Previous page
1/28
Next page
9
4. WIRE ROUTING
4.1 MAIN POWER WIRES
Run the positive main power cable („+12 V“) directly from the positive terminal of the car battery to
the amplifier’s detachable power terminal. For protection of your car audio system against electrical
fire hazards, resulting from a short-circuit of the main power cable to chassis ground a main fuse
holder must be inserted within the first 30 cm of the positive main power cable.
The applicable fuse value must be matched to the limitations of your main power cable AND the cur-
rent draw of the amplifier – therefore choose an appropriate fuse value.
Attach the ground cable to the amplifiers detachable power terminal. In most cases
it will be best to keep the ground cable („-12V“) as short as possible, i.e. to find a chassis contact
very close to the amplifier. The ground power wire must have the same cross-section as the positive
power cable. The contact point where the ground wire is attached to, must be solid and clean, i.e.
free from rust or paint!
Before connecting the detachable plug to the amplifier, tighten both power input terminals of the plug,
and double check for perfect fit of both main cable leads!
4.2 RCA & REMOTE WIRES
Carefully run the audio signal interconnects, the amp remote wire and if applicable - the cable of the
low pass level remote control from the head-unit or dashboard to the amplifier. As mentioned before,
the audio signal cables should always be routed completely separate from the power cables. Connect
the remote (turn on/turn off) lead to the respective input terminal of the amplifier and to the remote
output of your head-unit. Now you can connect the RCA interconnects to the respective outputs of
your head-unit and to the inputs of the amplifier. The remote low pass level remote control unit can be
mounted in any convenient position where it can be reached while you drive in your car.
4.3 REMOTE & LOUDSPEAKER WIRES
Once the remote and speaker cables have been routed, turn loose the screws of the detachable speaker
terminal and after inserting the stripped remote and speaker cables re-tighten the screws. When
baring wires for connection, remove approximately 6-8mm of the insulation and after axially twisting
the wires, insert the bare ends into the corresponding speaker terminal output on the detachable plug.
At least connect the detachable terminal to the amplifier.
Close the electrical circuit by inserting the main fuse. Now switch on your head unit. The blue
OPERATING LED of the remote control panel should light-up. If the LED lights up red, your installation
is wrong! Immediately turn off your head-unit and carefully re-check all installation steps!
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emphaser ea 1500 flx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emphaser ea 1500 flx in the language / languages: English, German as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info