168847
8
Zoom out
Zoom in
Previous page
1/28
Next page
8
2.4 SPEAKER IMPEDANCES & WIRE INFO
The heat dissipation capacity of this amplifier has been designed to cope with low impedance loads.
However, EMPHASER laboratories recommend staying at or above the suggested impedance ratings
listed below:
EA1500FLX
2 ohms mono
2 x EA1500FLX in Master/Slave configuration: 4 ohms mono
Note: EMPHASER laboratory recommends a minimum main power cable cross-section (5m total
length) of minimum 25mm² and 35 mm², when the amp is intended to be operated at full output power
for prolonged periods of time. To reduce the diameter down to 25 mm², please use an according
power distribution block.
These recommendations guarantee trouble-free operation of your amplifier, giving you full power
output.
3. AMPLIFIER MOUNTING
Attention! For your own safety, disconnect the positive battery terminal (+12V)
or remove the main fuse in the positive power cable near the car battery, before
you start any wiring work!
Before you proceed to install this EMPHASER amplifier, it is recommended to map out the complete
audio system and the respective wiring required. Consider all additional electrical requirements and
accessories, such as power cables, interconnect cables etc., to complete this install. Please note that
- because of possible interference problems with the existing car electrics and electronics - especially
the routing of the signal cables and the chassis ground connection will have a profound impact on a
trouble-free (noise free!) operation of the amplifier.
The mounting location should be carefully selected and in the interest of passive driver and passenger
safety, the amplifier must be securely mounted. Make sure that there is no wiring harness, fuel tank
etc. behind or below the mounting surface that may be damaged by the drilling of the holes for the
amplifier mounting screws. After installation, there should be a clearance of at least 5cm on all sides
including the top of the amplifier heatsink. Make sure the unit is not exposed to direct sunlight, humi-
dity, water, oil or spill of other fluids that may enter the amplifier.
Once the location where the amplifier will be mounted is defined, use the unit as a template for the
marking of the mounting holes with pencil or felt-tip marker. The mounting holes should be pilot-drilled,
using a 2,5 mm or 3 mm drill bit. Make sure that the housing of the amp does not come into electrical
contact with the vehicle.
Important! There must not be a direct contact of the amplifier heatsink, bottom
panel or other metal parts to the vehicle chassis ground! Electrical ground-loops
can result in audible hum!
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emphaser ea 1500 flx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emphaser ea 1500 flx in the language / languages: English, German as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info