499611
7
Zoom out
Zoom in
Previous page
1/13
Next page
7 | ENGLISH
Warning! Take notice of the following before installing the EM6557.
If you do not have enough electrical skills, do not continue and let a certified
electrician do the job for you. Otherwise you might get injured and/or electrocuted.
If you do have enough skills, be very careful. Take notice of the following:
Disable the mains of your house by turning off the main switch, before you
continue. Otherwise you might get injured and/or electrocuted.
In some older houses the colours of the wiring can be different. In some
situations not all wires are available in the junction box or wall switch housing.
You might need to run one or more extra wires from the nearest distribution box.
Do not install the Built-In Switch near combustible substances or any source of
heat, e.g. fires, radiators, boilers etc.
Do not install the Built-In Switch facing direct sunlight, humid or dusty places.
Use terminal blocks or wire nuts to cover unused cables.
Eminent cannot be held liable nor responsible for any damage caused during the
installation and/or using the device afterwards.
Before you start to install, make sure you have the proper tools at hand. For example:
Screwdrivers
Wire terminals or wire nuts
Wire stripper
Adhesive tape to colour cables (if necessary)
1. Take the Built-In switch out of the packaging.
2. Check if the power is really switched off (for example by using a voltage tester).
3. Open the junction box where you want to install the Built-In switch. Remove the
light luminary if present.
4. Connect the blue neutral wire of the lamp with the left N output of the Built-In
switch and tighten the screw.
5. Connect the switching wire of the lamp with the LS input of the Built-In switch.
Often this wire has a black colour.
6. Connect the blue neutral wire of the mains with the N input (middle) of the Built-In
switch and tighten the screw.
7. Connect the 230v live wire of the mains with the L input of the Built-In switch.
Often this wire has a brown colour.
8. Check if a black switching wire or brown wire is coming from the junction box and
is running directly to the first wall switch.
a. If so: Connect the white switching wire to the brown wire running to the
first wall switch.
Use black or white adhesive tape to colour the brown wire black or white.
This will help you to remember that the brown wire is not a live wire
anymore.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eminent EM6557 - e-Domotica at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eminent EM6557 - e-Domotica in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eminent EM6557 - e-Domotica

Eminent EM6557 - e-Domotica User Manual - German - 14 pages

Eminent EM6557 - e-Domotica User Manual - Dutch - 14 pages

Eminent EM6557 - e-Domotica User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info