701980
6
Zoom out
Zoom in
Previous page
1/45
Next page
PREPARATION FOR USE
The appliance uses ordinary tap water.
If the water is very hard (hardness higher than27 degrees French).we suggest using distilled or de-
mineralized water.
Before using equipment, open the flap of water (15), added just the right amount of water to the
water tank (14), first is less than the MAX water level.
Connecting the appliance and power cord.
Press the main switch (8), power indicator light (8) lights up, it means the iron start running. In the
condition of the equipment only dry hot function.
At the same time, press the boiler switch (6), the boiler power light (6) and steam available indicator
light (7) light up, it means the boiler (12) start running. The appliance is the steam mode.
Feed-water from electromagnetism water pump coming down the boiler when the boiler(12) heating
enough. Choosing the temperature by temperature knob(3),the colored part indicate ironing area
which can be chose.
Around 90 seconds . Heating indicator(4) will die out , it means the appliance can be using the steam.
Around 3 minutes. Steam available light (7) will die out, it means the appliance can be using the
steam.
If you exit out the steam mode, you just press again the boiler switch button(6), the boiler power
indicator light (6) goes out, it means the appliance exits out the steam mode.
Cheak the manufacturers label on the garment, and interpret the symbol on the label as follows.
STEAM IRONING
When using the iron for the first time, iron a plain cloth first.
Obtain steam after pressing the steam button (2).
This appliance is also able to generate steam in a vertical position and can therefore be used to refresh
fabrics easily with a jet of steam.
If you hear the loud feed-water sound when you ironing, it means there is no water in the water
tank(14).Press the boiler button(6) and cut down the boiler power . After fill the water tank(14),then
press the boiler button(6) again ,go on ironing.
CAUTION! Never attempt to open the cleaning valve(10) while the boiler is under pressure.
DRY IRONING
Connect the appliance to the mains supply, only press the main switch(8), then select the desired
temperature by turning the thermostat knob(3).Wait until the iron heating indicator light (4) goes off,
indicating that the desired temperature has been reached.
PUTTING THE APPLIANCE AWAR
- After use, always allow the iron to cool before putting it away.
- It is not necessary to drain the boiler after ironing.
- Position the Steam flexible hose- Power cable get together in the base of the appliance10.
- Always keep the surface the ironing plate perfectly clean. To clean it, just wipe the cold surface with
a damp cloth. The appliance must not be cleaned with descaling agents.
- Do not iron over zippers, hooks, rings, etc; as these may scratch the plate.
- When you have finished ironing. Place the iron correctly on its stand. Ensure that there are no traces
of water under the plate, as these may cause stains.
- Store the appliance in a dry place
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emerio PH-122174 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emerio PH-122174 in the language / languages: English, German as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info