Manual Elro HIS20SF (page 8 of 62) (English, German, Dutch, French)

536726

Zoom out

Zoom in

1/62

REMOTE CONTROL UNIT

A LED indicator F Key Chain Ring

B Fully Arm/Holiday Arm G Battery Cover

C Night Arm/Partial Arm H Negative Polarity

D Disarm I Positive Polarity

E Panic Switch

The Remote Control Unit is used to Fully Arm/Holiday

Arm, Night Arm/Partial Arm and Disarm the system.

The Remote Control also incorporates a Panic switch.

Activating the Panic switch will immediately initiate a

Full Alarm condition whether the system is Armed or

Disarmed, (unless the system is in Service, Test or

Program mode).

The Remote Control adopts a CR2032 type Lithium cell

which under normal conditions will have typical life in

excess of 1 year. Under normal battery conditions the

LED on the Remote control will only illuminate when a

button is pressed. However, under low battery

conditions this LED will flash every time the button is

pressed. When this occurs the batteries should be

replaced as soon as possible.

SETTING THE REMOTE CONTROL

1. Remove the rear cover by undoing the small screw

on the rear of the Remote Control.

2. Insert the battery ensuring that the +v terminal

faces upwards away from the PCB.

3. Replace the rear cover and fixing screw.

4. In order to communicate with the Smart Home Box,

the ID code of the Remote Control needs to be

learned by the Smart Home Box.

a. Set the Smart Home Box into ‘1. User Setup’

and press .

b. Select which administrator/user will carry the

remote control and press .

c. Select ‘:7 Remoter’ and press .

d. ‘7-1 LearningID’ will be shown and press

By pressing the , or on the Remote

Control will emit the ID code to the Smart Home

Box instantly.

SMART HOME BOX

LOCATING THE SMART HOME BOX

When choosing a suitable location for the Smart Home

Box, the following points should be considered.

1. The Smart Home Box should be located in a

position out of sight of potential intruders and in a

safe location, but easily accessible for system

operation.

2. The Smart Home Box should be mounted on a

sound flat surface to ensure that the rear tamper

switch on the Smart Home Box is closed when the

Panel is mounted. The Smart Home Box should

be mounted at a convenient height of between

1.3m and 1.5m and in a position where it will be

seen each day.

Note: If small children are in the household, a

further consideration should be given to keeping

the units out of their reach.

3. It is recommended that the Smart Home Box

should be positioned such that the Exit/Entry tone

(emitted by the Smart Home Box) can be heard

from outside the property.

4. The Smart Home Box should be mounted within a

protected area so that any intruder cannot reach

the Smart Home Box without opening a protected

door or passing through an area protected by a

PIR detector when the system is armed.

5. The Smart Home Box must be located within reach

of a mains socket.

6. If the telephone based functionality is to be used

then the Smart Home Box will need connecting to a

convenient telephone point.

Note: It is recommended that the telephone

connection lead is not extended beyond 5m before

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elro HIS20SF in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elro HIS20SF Manual

Product: