536725
18
Zoom out
Zoom in
Previous page
1/34
Next page
-49--16-
MAGNETIC CONTACT DETECTOR(S)
The Magnetic contact consists of two parts; a Detector and a Magnet. They are
designed to be fitted to doors or windows with the Magnet mounted on the
opening part and the Detector mounted on the fixed frame. Opening the
protected door/window will remove the magnetic field, trigger the Detector and
generate an alarm condition, (if the system is armed and the alarm zone
active).
The Detector is powered by one 3.6V 1/2 AA size Lithium cells which under
normal conditions will have typical life in excess of 5 years. Under normal
battery conditions with battery cover fitted the LED on the Detector will not
illuminate when the Detector is triggered, (unless in test mode). However, under
low battery conditions this LED will be illuminated when the detector is
triggered. When this occurs the battery should be replaced as soon as possible.
1. Use the and buttons to scroll through the menu until ‘WALK TEST
is displayed.
Press to activate Walk Test. ‘Walk Test Waiting…’ will be displayed.
2. Walk into and move slowly around the protected area, each time the detector
senses movement the LED behind the lens will flash. In addition, the Control
Panel will beep to indicate that the alarm signal has been received and the
identity of the zone that the detector is configured for will be displayed.
If necessary adjust the detection range by changing the mounting position of
the PCB within the PIR housing.
Note: In normal operation, the LED behind the PIR lens will not flash on
movement detection, (unless the battery is low).
If necessary re-adjust the detection pattern by changing the mounting
position of the PCB within the PIR housing.
3. Remove the back cover of the PIR detector. The Control Panel should beep
and display ‘PIR Detector Tamper’ to show that the detector’s tamper switch
has been activated.
4. Press to return to the top level menu of TEST MODE.
5. Reconfigure the PIR Detector for normal mode by setting DIP1 of SW2 to OFF
and refit in position.
Note: When the detector is fully installed i.e. battery cover is refitted; the
unit will not detect movement for approximately 2 minutes after each
activation. (This feature is present to conserve battery power and maximize
the battery life).
Default setting: ON
Scroll through the menu until ‘5-2 Entry Delay Beep’ is displayed.
The current setting will also be displayed.
To change the setting press .
Press to enable the Entry-delay beep, or
Press to disable the Entry-delay beep.
EXIT DELAY BEEP
This controls the warning beep which operates during the Exit Delay period
when Full Arm is initiated.
Default setting: ON
Scroll through the menu until ‘5-3 Exit Delay Beep’ is displayed. The current
setting will also be displayed.
To change the setting press .
Press to enable the Exit-delay beep, or
Press to disable the Exit-delay beep.
PARTIAL ARM 1 SETUP
PROGRAM MODE
Code:
6. PARTIAL ARM 1
6-1Exit Delay
xx xxx SEC
Select
ON->* OFF->#
Input
(1-250) Secs
Select
ON->* OFF->#
6-2 Entry Delay
Beep: xxx
6-3 Exit Delay
Beep: xxx
Scroll through the programming menu until ‘6. PARTIAL ARM 1’ is displayed
and press .
Note: After configuring Partial Arm 1 press to return to the top level
programming menu.
ENEN
Select
ON-> OFF->#
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro HA68S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro HA68S in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro HA68S

Elro HA68S Quick start guide - English - 1 pages

Elro HA68S Quick start guide - German - 1 pages

Elro HA68S User Manual - German - 34 pages

Elro HA68S Quick start guide - Dutch - 1 pages

Elro HA68S User Manual - Dutch - 34 pages

Elro HA68S Quick start guide - French - 1 pages

Elro HA68S User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info