536725
11
Zoom out
Zoom in
Previous page
1/34
Next page
-9--56-
MOUNTING THE CONTROL PANEL
1. Undo the two captive fixing screws on top of the panel and open the cover.
The cover is hinged along the bottom edge.
2. Unclip and remove the two back-up batteries on either side of the panel.
3. Hold the Control Panel in position on the wall and mark the positions of the
four fixing holes. Remove the Panel and drill four 5mm holes and fit the
25mm Wall Plugs.
IMPORTANT: Do not drill the fixing holes with the Control Panel in position;
as the resulting dust and vibration may damage the Control Panel’s internal
components and invalidate the guarantee.
4. Fit two 18mm No.4 screws into the top holes until almost fully home and hang
the Control Panel over these screws using the two keyhole slots in the top
corners of the panel casing.
5. Route the cable from the Power Supply Unit up behind and on the right hand
side of the Control Panel and connect the plug to the DC power socket in the
panel. Ensuring that the cable is not trapped between the panel and the wall.
6. Fix the Panel to the wall using two 18mm No. 4 screws in the lower two fixing
holes in the panel and tighten the upper fixing screws until they just grip the
casing. Do not over tighten the fixing screws as this could damage or distort
the casing.
7. Ensure that the ‘Reset’ and the ‘Hard-Wired
Siren tamper detect’ jumper links are set in the OFF position.
8. Connect battery leads to both back-up batteries and refit batteries.
Battery 1 (left): Red lead to +ve battery terminal
Blue lead to –ve battery terminal
Battery 2 (right): Blue lead to +ve battery terminal
Black lead to –ve battery terminal
IMPORTANT: Take care when connecting battery leads to the batteries as
connecting incorrectly could damage the batteries or the Control Panel.
Note: The Power LED may flash to indicate that the unit is being operated
from the back-up batteries and that mains supply is not present.
9. If fitted, remove the plastic film covering the LCD display and on the display
window on the cover.
10. Close the lid of the Control Panel and tighten the captive fixing screws.
11. Plug in and switch ON the Power Supply Unit, (the Power LED should
illuminate).
ARM
The system can be set in ARM mode using either the Remote Control or the
Control Panel as follows:
Remote Control:
Press the ‘ARM’ button,
Control Panel:
Press the Arm button followed by the User Password and then the Enter button:
User Password
By pressing , the programmed exit delay will be overrided to 5 seconds.
PART-ARM 1
The system can be set in PARTIAL Arm 1 mode using either the Remote Control
or the Control Panel as follows:
Remote Control:
Press the ‘PARTIAL ARM’ button, .
Control Panel:
User Password
By pressing , the programmed exit delay will be overrided to 5 seconds.
PARTIAL ARM 2
The system can be set in Partial Arm 2 mode using either the Remote Control or
the Control Panel as follows:
Remote Control:
Press the ‘PARTIAL ARM’ button twice, , .
Control Panel:
User Password
By pressing , the programmed exit delay will be overrided to 5 seconds.
DISARM
The system can be Disarmed using either the Remote Control or the Control
Panel as follows:
ENEN
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro HA68S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro HA68S in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro HA68S

Elro HA68S Quick start guide - English - 1 pages

Elro HA68S Quick start guide - German - 1 pages

Elro HA68S User Manual - German - 34 pages

Elro HA68S Quick start guide - Dutch - 1 pages

Elro HA68S User Manual - Dutch - 34 pages

Elro HA68S Quick start guide - French - 1 pages

Elro HA68S User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info