536725
9
Zoom out
Zoom in
Previous page
1/34
Next page
-7--58-
A LED indicator F Key Chain Ring
B Arm G Battery Cover
C Partial Arm H Negative Polarity
D Disarm I Positive Polarity
E Panic Switch
The Remote Control Unit is used to Arm, Partial Arm and Disarm the system.
The Remote Control also incorporates a Panic switch. Activating the Panic switch
will immediately initiate a Full Alarm condition whether the system is Armed or
Disarmed, (unless the system is in Service, Test or Program mode).
The Remote Control adopts a CR2032 type Lithium cell which under normal
conditions will have typical life in excess of 1 year. Under normal battery
conditions the LED on the Remote control will only illuminate when a button is
pressed. However, under low battery conditions this LED will flash every time
the button is pressed. When this occurs the batteries should be replaced as
soon as possible.
SETTING THE REMOTE CONTROL
1.Remove the rear cover by undoing the small screw on the rear of the Remote
Control.
2.Insert the battery ensuring that the +v terminal faces upwards away from
the PCB.
REMOTE CONTROL UNIT
Front Back
B
C
D
A
E
G
F
H
I
CHIME
The Chime facility can only be operated with the system in Disarm mode.
Press to toggle the Chime facility between ON and OFF.
Note: If the Chime is ON and the system is then armed the Chime will remain
ON after the system is disarmed.
MUTE
The Mute facility can only be operated with the system in Disarm mode.
Press to toggle the Mute facility between ON and OFF.
Note: If the Mute is ON, no voice guidance will be made during operation. If the
mute is OFF, voice guidance will be active. However, if ‘LINE STATUS’ LED
illuminates while the mute is OFF, there is no voice guidance will be available.
LATCH KEY
Press to access the latch key function for quick programming.
EVENT-LOG
The Event Log will store the last 50 system Arm, disarm, alarm and detector
Low Battery events. The Event Log will record the time, date and details for
each event. If when the system is disarmed the “ALARM MEM’ LED is flashing
and the panel beeps every 10s, this indicates that an alarm has occurred. To
cancel the LED and stop the beeping you must access the event log or press
to eliminate the flashing ‘ALARM MEM’ LED and the beeping as well.
To access the Event Log, (with the system in Disarm):
Press .
The Event-Log will automatically start scrolling through and displaying the event
data starting with the most recent event. The data for each event is shown on
two screens, each screen will be displayed for 5 seconds before moving on to
the next screen and then the next event.
Use the and buttons to manually scroll through the event log to the
required position as necessary.
Press to return to Disarm.
TELEPHONE LINE DETECTION
When setting to the voice dialer and If ‘LINE STATUS’ LED is flashing, it implies
bad telephone line connection or telephone network being out of order. Check
the telephone line and re-test it.
When setting to the digital dialer and if ‘LINE STATUS’ LED is flashing, it implies
two causes of failure. One is bad telephone line connection or telephone
network being out of order. The other cause of failure is derived from the
central monitoring station. Consult with the central monitoring station for help.
ENEN
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro HA68S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro HA68S in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro HA68S

Elro HA68S Quick start guide - English - 1 pages

Elro HA68S Quick start guide - German - 1 pages

Elro HA68S User Manual - German - 34 pages

Elro HA68S Quick start guide - Dutch - 1 pages

Elro HA68S User Manual - Dutch - 34 pages

Elro HA68S Quick start guide - French - 1 pages

Elro HA68S User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info