621095
12
Zoom out
Zoom in
Previous page
1/23
Next page
- 23 -
In the surveillance applications, alarm video/audio is much more important than normal video/audio. So, this digital video/audio
r
ecorder is designed to allow the user to divide each HDD into alarm partition and normal partition. And, alarm video/audio will be
recorded in alarm partition, normal video/audio in normal partition.
The HDD Setup allows the administrator to format/clear each HDD, set Alarm Record size and Normal Record size of each HDD,
and define the behaviors for Alarm Record and Normal Record if it reaches the end of the last HDD in the system.
The general operations are as follows:
▲▼◄►
Press these buttons to select the items.
M
ODE => Format/Clear
Press this button to format/clear the HDDs as described in Section 6.6.1.
ESC
Press this button to escape from this screen, and return to Setup Menu display. If the Save dialog is shown, press ENTER to
exit and save, ESC to exit without saving.
The following is a brief description for each item and its specific operations:
S
ize (GB) the total HDD storage in GB (Giga-Byte) for Alarm Record and Normal Record respectively. This item is just for
information. Please refer to Section 6.6.1
for more detailed information and setup of each individual HDD.
A
uto Overwrite automatic overwrite of the recorded video/audio from HDD#1 when the Alarm/Normal Record disk drive
capacity reaches the end of the last HDD. If Auto Overwrite is disabled and the Alarm/Normal Record disk drive capacity
reaches the end, the system will not overwrite the recorded video/audio, and hence not record Alarm/Normal video/audio, until
the user presses the Alarm Reset button. Press ENTER or +/- to check/uncheck this item. The default setting is ˇ
ˇˇ
ˇ -
checked.
H
DD Full Action actions when Alarm/Normal Record disk drive capacity reaches the end of the last HDD. Press ENTER
or +/- to check/uncheck this item. The default setting is “ˇ
ˇˇ
ˇ ” - checked.
Duration response duration to define at most how long (in seconds) the Alarm Out relay and the Buzzer will keep being
triggered after the corresponding partition, Alarm Record or Normal Record, is full. Press +/- buttons to adjust the value (3-60
seconds, discrete).
Alarm Out to define which Alarm Output will be triggered when the corresponding partition, Alarm Record or Normal
Record, is full. Press +/- buttons to select none (N/A) or one of the Alarm Outputs (1-2).
Buzzer to activate the internal Buzzer or not when the corresponding partition, Alarm Record or Normal Record, is full.
Press ENTER or +/- to check/uncheck this item. The default setting is “ˇ
ˇˇ
ˇ ” - checked.
Log – to log to event logs or not. Press ENTER or +/- to check/uncheck this item. The default setting isˇ
ˇˇ
ˇ ” - checked.
E-mailto send the event e-mail to remote station or not. The e-mail will be sent to the predefined receivers when the event
is triggered. Press ENTER or +/- to check/uncheck this item. The default setting is “
” - unchecked.
6
.6.1 HDD Format/Clear
In HDD Setup display, press M
ODE to call up HDD Format/Clear screen as shown.
The HDD must be formatted before it can be used to record video/audio. T
he HDD Format/Clear screen allows the
administrator to format and/or clear each HDD, and set the size for Alarm Record partition and Normal Record partition for each
HDD. Please use only HDD with maximum storage size as 500GB, and make sure there’s no remote user before formatting
the HDD.
The general operations are as f
ollows:
M
ODE => Format
Press this button to format the HDD. A confirmation dialog will be shown on the screen, press ENTER to confirm, or ESC to
- 24 -
cancel. P
lease note that it would take about 40 seconds to format a brand new HDD.
Note: If the HDD has not been formatted yet, it will be formatted and partitioned with default record size, 30% for Alarm
record and 70% for Normal record. If it has been formatted before, it will be formatted according to the Alarm REC Size
(%) and Normal REC Size (%) displayed on the screen, but the previously recorded contents within the new size won’t
be cleared and will be accessible.
SEQ => Clear
Press this button to clear the HDD. A confirmation dialog will be shown on the screen, press ENTER to confirm, or ESC to
cancel.
Note: If the HDD has not been formatted yet, it will be formatted and partitioned with default record size, 30% for Alarm
r
ecord and 70% for Normal record. If it has been formatted (and recorded) before, it will be partitioned according to the
Alarm Record Size (%) and Normal Record Size (%) displayed on the screen, and the previously recorded contents will
all be cleared.
C
ALL => Physical Format
Press this button to physically format the selected HDD. A confirmation dialog will be shown on the screen, press ENTER to
confirm, or ESC to cancel. Please note that the recording will be always optimized for performance & lifetime no matter
it
’s for the first time or for the one hundredth time. The formatting would take less than 1 minute. We strongly
recommend that the user use this physical format function to format the HDD for the first time.
Note: The HDD will be physically formatted and partitioned with default record size, 30% for Alarm record and 70% for
N
ormal record. All the previously recorded contents will be cleared.
E
SC
Press this button to escape from this screen, and return to HDD Setup display. If the Save dialog is shown, press ENTER to
exit and save, ESC to exit without saving.
The following is a brief description for each item and its specific operations:
Size (GB) – the total storage in GB (Giga-Byte) for the HDD if it has been formatted. This item is just for information.
Alarm Record(%) Alarm Record Size (in percentage) for this HDD. Please follow the Text Input method described in
Section 4.1
to change the value.
Normal Record(%)Normal Record Size (in percentage) for this HDD. It equals to (100% - Alarm Record Size). This item
is just for information.
6
.7 Password Setup
In Setup Menu display, press
to change the highlighted option to Password, and then press ENTER to call up Password
Setup as shown.
The Password Setup allows the administrator to add new users, delete existing ones, and/or modify the users name, password,
a
nd/or level.
There are three password levels in the system, including A
dministrator (highest), Supervisor, and Operator (lowest). The
Operator can operate live video display, the Supervisor live video display, image playback and archive, and the Administrator
everything. The system allows up to 18 user accounts.
There is one factory-preset login name/password aa/11 at A
dministrator level. The user can use it to login the system for the first
time.
The general operations are as f
ollows:
◄►
Press these buttons to select the items. The display will scroll up/down if the selected item is not shown on the screen.
MODE => Set default login
Pr
ess this button to select this user as the default one at login, or deselect if this user is the default login user. An asterisk (*)
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro DVR154S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro DVR154S in the language / languages: English as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro DVR154S

Elro DVR154S User Manual - German - 24 pages

Elro DVR154S User Manual - Dutch - 22 pages

Elro DVR154S User Manual - French - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info