704004

Elna eXtend 264 Manual

76
Zoom out
Zoom in
Previous page
1/84
Next page
70
CARE OF YOUR MACHINE
Replacing the Upper Knife
To remove:
z
Turn off the power switch and unplug the machine.
x
Open the looper cover and side cover.
c
Deactivate the upper knife.
v
Remove the hexagonal bolt, and remove the upper
knife.
q
Upper knife
w
Hexagonalbolt
e
Stopperpin
r
Lowerknife
36
Replacing the Upper Knife
To remove:
1.
Turn off the power switch and unplug the machine.
2. Open the looper cover and side cover.
3. Deactivate the upper knife.
4. Remove the hexagonal bolt, and remove the
upper knife.
Upper knife
Hexagonal bolt
Stopper pin
Lower knife
To attach:
1. Insert new upper knife into the groove of knife
holder and stopper pin, then tighten the
hexagonal bolt slightly.
2. Turn the upper knife holder to cutting position.
3. Turn the handwheel toward you until the upper
knife comes to its lowest position.
Loosen the hexagonal bolt, and adjust the
position of the upper knife so that the edge of the
upper knife overlaps 0.8 to 1.5 mm (3/64´´) from
the edge of lower knife as illustrated.
Then tighten the hexagonal bolt firmly.
4. Close the looper cover and side cover.
Cleaning Upper Knife Area
1.
Turn off the power switch and unplug the machine.
2. Open the looper cover.
Remove the waste pieces to the front with a lint
brush or waste scraps.
 You may use a vacum cleaner to clean the upper
knife area or feed dog.
 The lower knife will last over one year in normal
use. However, if you run over a pin or a hard
object, it may be required to replace both upper
and lower knives at the same time.
CARE OF YOUR MACHINE
0.8 ~ 1.5 mm (3/64˝)
36
Replacing the Upper Knife
To remove:
1.
Turn off the power switch and unplug the machine.
2. Open the looper cover and side cover.
3. Deactivate the upper knife.
4. Remove the hexagonal bolt, and remove the
upper knife.
Upper knife
Hexagonal bolt
Stopper pin
Lower knife
To attach:
1. Insert new upper knife into the groove of knife
holder and stopper pin, then tighten the
hexagonal bolt slightly.
2. Turn the upper knife holder to cutting position.
3. Turn the handwheel toward you until the upper
knife comes to its lowest position.
Loosen the hexagonal bolt, and adjust the
position of the upper knife so that the edge of the
upper knife overlaps 0.8 to 1.5 mm (3/64´´) from
the edge of lower knife as illustrated.
Then tighten the hexagonal bolt firmly.
4. Close the looper cover and side cover.
Cleaning Upper Knife Area
1.
Turn off the power switch and unplug the machine.
2. Open the looper cover.
Remove the waste pieces to the front with a lint
brush or waste scraps.
 You may use a vacum cleaner to clean the upper
knife area or feed dog.
 The lower knife will last over one year in normal
use. However, if you run over a pin or a hard
object, it may be required to replace both upper
and lower knives at the same time.
CARE OF YOUR MACHINE
0.8 ~ 1.5 mm (3/64˝)
36
Replacing the Upper Knife
To remove:
1.
Turn off the power switch and unplug the machine.
2. Open the looper cover and side cover.
3. Deactivate the upper knife.
4. Remove the hexagonal bolt, and remove the
upper knife.
Upper knife
Hexagonal bolt
Stopper pin
Lower knife
To attach:
1. Insert new upper knife into the groove of knife
holder and stopper pin, then tighten the
hexagonal bolt slightly.
2. Turn the upper knife holder to cutting position.
3. Turn the handwheel toward you until the upper
knife comes to its lowest position.
Loosen the hexagonal bolt, and adjust the
position of the upper knife so that the edge of the
upper knife overlaps 0.8 to 1.5 mm (3/64´´) from
the edge of lower knife as illustrated.
Then tighten the hexagonal bolt firmly.
4. Close the looper cover and side cover.
Cleaning Upper Knife Area
1.
Turn off the power switch and unplug the machine.
2. Open the looper cover.
Remove the waste pieces to the front with a lint
brush or waste scraps.
 You may use a vacum cleaner to clean the upper
knife area or feed dog.
 The lower knife will last over one year in normal
use. However, if you run over a pin or a hard
object, it may be required to replace both upper
and lower knives at the same time.
CARE OF YOUR MACHINE
0.8 ~ 1.5 mm (3/64˝)
To attach:
z
Insert new upper knife into the groove of knife holder
and stopper pin, then tighten the hexagonal bolt
slightly.
x
Turn the upper knife holder to cutting position.
c
Turn the handwheel toward you until the upper knife
comes to its lowest position.
Loosenthehexagonalbolt,andadjusttheposition
of the upper knife so that the edge of the upper knife
overlaps 0.8 to 1.5 mm (3/64´´) from the edge of lower
knife as illustrated.
Thentightenthehexagonalboltrmly.
v
Close the looper cover and side cover.
Cleaning Upper Knife Area
z
Turn off the power switch and unplug the machine.
x
Open the looper cover.
Remove the waste pieces to the front with a lint brush
or waste scraps.
* You may use a vacuum cleaner to clean the upper knife
area or feed dog.
* The lower knife will last over one year in normal use.
However,ifyourunoverapinorahardobject,itmay
berequiredtoreplacebothupperandlowerknivesat
the same time.
… 76 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elna eXtend 264 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elna eXtend 264 in the language / languages: English, German, French as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info