612699
69
Zoom out
Zoom in
Previous page
1/94
Next page
ELM327
69 of 94ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
Programmable Parameters (continued)
rate, or the Carriage Return character, for example,
and forget what you have set them to. The Carriage
Return value that is set by PP 0D is the only character
that is recognized by the ELM327 as ending a
command, so if you change its value, you may not be
able to undo your change. In this case, your only
recourse may be to force all of the PPs off with a
special hardware trick.
When the ELM327 first powers up, it looks for a
jumper between pin 28 (the OBD Tx LED output) and
circuit common (VSS). If a jumper is in place, it will turn
off all of the PPs for you, restoring the IC to the factory
default settings. To use this feature, simply connect a
jumper to circuit common (which appears in numerous
places - pins 8 or 19 of the ELM327, pin 5 of an
RS232 connector, one end of most capacitors, or at
the OBD connector), then hold the other end of the
jumper to pin 28 while turning the power on. When you
see the RS232 Rx LED begin to flash quickly, remove
the jumper – the flashing LED means that it worked
and the PPs are all off.
This feature should only be used when you get
into serious trouble, and it’s your only choice (since
putting a jumper into a live circuit might cause damage
if you put it into the wrong place). Be careful if you
need to use it.
0A Linefeed Character 0A R00 to FF
Programmable Parameter Summary
The following pages provide a list of the currently
available Programmable Parameters. The character
shown in the ‘Type’ column indicates when changes
will take effect. Possible values are:
I - the effect is Immediate,
D - takes effect after Defaults are restored
(AT D, AT Z, AT WS, MCLR or power off/on)
R - takes effect after a Reset
(AT Z, AT WS, MCLR or power off/on)
P - needs a Power off/on type reset
(AT Z, MCLR, or power off/on)
01 Printing of header bytes (AT H default setting) D
02 Allow long messages (AT AL default setting) D
03 NO DATA timeout time (AT ST default setting)
setting = value x 4.096 msec
00 to FF 32
(205 msec)
D
00 Perform an AT MA command after powerup or reset FF
(OFF)
R00 = ON
FF = OFF
FF
(OFF)
FF
(OFF)
00 = ON
FF = OFF
00 = ON
FF = OFF
PP Description Values Default Type
06 OBD Source (Tester) Address. Not used for J1939 protocols. F1 R00 to FF
00 to 02 01 D04 Default Adaptive Timing mode (AT AT setting)
07 ILast Protocol to try during automatic searches 0901 to 0C
09 Character echo (AT E default setting) R00
(ON)
00 = ON
FF = OFF
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elm 327 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elm 327 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info