612699

Elm 327 Manual

68
Zoom out
Zoom in
Previous page
1/94
Next page
Programmable Parameters
The ELM327 contains several memory locations
that retain their data even after power is turned off.
Every time the IC is reset, these locations are read
and used to change the default settings for such things
as whether to display the headers, or how often to
send ‘wakeup’ messages. Because they define the
operation of the ELM327, we refer to these memory
locations as the Programmable Parameters.
All of the Programmable Parameters are easily
altered at any time using a few simple commands.
These commands are standard AT Commands, with
one exception: each one requires a two-step process
to complete. This extra step provides some security
against random inputs that might otherwise cause
changes.
As an example of how to change a Programmable
Parameter, consider PP 01 (shown on page 69) which
sets the default state for the AT H command. If you are
constantly powering your ELM327 and then using
AT H1 to turn the headers on, you may want to change
the default setting, so that the headers are always on
by default. To do this, simply set the value of PP 01 to
00:
>AT PP 01 SV 00
OK
This changes the value associated with PP 01, but
does not yet enable it. To make the change effective,
you must also type:
>AT PP 01 ON
OK
At this point, you have changed the default setting
for AT H1/H0, but you have not changed the current
AT H1/H0 setting. From the ‘Type’ column in the table
on page 69, you can see that PP 01 is a type ‘D’
parameter, so the change only becomes effective the
next time that defaults are restored. This could be from
a reset, a power off/on, or possibly an AT D command.
If you send the command AT D, then you should find
that the headers are now displayed by default.
As there are many Programmable Parameters that
you can alter, it might occasionally be difficult to know
what changes you have made to them. To help with
that, the ELM327 provides a Programmable Parameter
Summary (PPS) command. This command simply
prints a list of the entire range of PPs (whether
currently supported or not), their current value, and
whether they are on/enabled (N), or off/disabled (F).
For a version 2.1 ELM327, with only the headers
enabled (PP 01, as discussed above), the summary
table would look like:
>AT PPS
00:FF F 01:00 N 02:FF F 03:32 F
04:01 F 05:FF F 06:F1 F 07:09 F
08:FF F 09:00 F 0A:0A F 0B:FF F
0C:68 F 0D:0D F 0E:9A F 0F:D5 F
10:0D F 11:00 F 12:FF F 13:55 F
14:50 F 15:0A F 16:FF F 17:6D F
18:31 F 19:31 F 1A:FF F 1B:FF F
1C:03 F 1D:0F F 1E:4A F 1F:FF F
20:FF F 21:FF F 22:FF F 23:FF F
24:00 F 25:00 F 26:00 F 27:FF F
28:FF F 29:FF F 2A:3C F 2B:02 F
2C:E0 F 2D:04 F 2E:80 F 2F:0A F
You can see that PP 01 now shows a value of 00,
and it is enabled (oN), while the others are all off.
Another example shows how you might change
the CAN filler byte. Some systems use ‘AA’ as the
value to send for unused CAN data bytes, while the
ELM327 uses ‘00’ by default. To change the ELM327
in order to have it send AAs instead, simply change
PP 26:
>AT PP 26 SV AA
OK
>AT PP 26 ON
OK
Again, PP 26 is of type ‘D’, so the above change
will not actually take effect until the defaults are
restored, whether it be by an AT D command, or by
resetting the ELM327.
The Programmable Parameters are a great way to
customize your ELM327 for your own use, but you
should do so with caution if using commercial
software. Most software expects an ELM327 to
respond in certain ways to commands, and may be
confused if the carriage return character has been
redefined, or if the CAN response shows a data length
code digit, for example. If you make changes, it might
be best to make small changes and then see the effect
of each, so that it is easier to retrace your steps and
‘undo’ what you have done, should you have to. If you
get in too deeply, don’t forget the ‘all off’ command:
>AT PP FF OFF
No matter what software you use, you might get
into more serious trouble, should you change the baud
ELM327
68 of 94ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
… 68 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elm 327 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elm 327 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info