741485
13
Zoom out
Zoom in
Previous page
1/20
Next page
(((ELKRON)))
MP110 USER MANUAL
(((ELKRON)))
MP110 USER MANUAL
7. System Test
- Enter the access MASTER code.
- Press key
F
+ key
3
. All leds turn on. A 30s delay is armed
during which the system test is carried out.
- By pressing kei
SIREN
1
, you access the alarm siren test and all allarm
actuator can be tested for 5s. To stop the alarm, press
SIREN
1
again
or
EXIT
F
.
- By pressing key
ZONE
3
, you access the input test procedure, any alarm
memory is turned off and a 10min delay is armed , after which you
automatically quit the test.
- After arming the test procedure, the sensor effectiveness can be tested
by means of the WALK-TEST (you walk in front of the sensor). The
display will show the number of the sensor in alarm, while the buzzer will
generate a sound for 5 seconds.
- If you walk in front of a “disabled” sensor, it is visualized on the display
but the buzzer will generate no sound. This means that a disabled input
is only stored but generates no alarm.
- By pressing key
EXIT
F
from procedure, then it is possible to see the
tested inputs resulted effective by means of the stored alarm visualiza-
tion procedure (key
A
+ key
1
) .
NOTE:
The test phase is signalled on all keypads and all commutators of the
plant by means of appropriate indications on the displays and the slow
flashing of the 3 sector leds.
8.Telephone Number Programming
1. Enter MASTER USER access code
2. Press key
EXIT
F
+
TEL
9
+
O
in sequence.
3. The display visualizes the first programmed telephone number: “Tn:
nnnn——n” (if there is no programmed telephone number, there will be
empty characters).
4. To go to other available numbers, if any, use keys
1
and
2
.
13
The display will show the characters “ ” flashing to show the
introduction of the year.
Enter a value from 00 to 99 (2 digits).
To confirm and store the entered date, press key
F
.
The system carries out no control on the consistency of the entered
data; the operator shall therefore ascertain that the programmed day/
month data are correct before confirming. In case of correct data, the
new date is stored and the positive result of the operation is confirmed
by an OK beep. When quitting by timeout, the modification is not saved
7. System Test
Enter the access MASTER code.
Press key
F
+ key
3
. All leds turn on while any alarm memory
turns off. A 30s delay is armed during which the system test is carried
out.
By pressing key
SIREN
1
, you access the alarm siren test and all alarm
actuators can be tested for 5s. To stop the alarm , press
SIREN
1
again
or
EXIT
F
.
By pressing key
ZONE
3
, you access the input test procedure, any alarm
memory is turned off and a 10min delay is armed , after which you
automatically quit the test.
After arming the test procedure, the sensor effectiveness can be tested
by means of the WALK-TEST (you walk in front of the sensor). The
display will show the number of the sensor in alarm, while the buzzer will
generate a sound for 3 seconds.
If you walk in front of a “disabled” sensor, it is visualized on the display
but the buzzer will generate no sound. This means that a disabled input
is only stored but generates no alarm.
By pressing key
EXIT
F
from procedure, then it is possible to see the
tested inputs resulted effective by means of the stored alarm visualiza-
tion procedure (key
A
+key
1
) .
28
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron MP110TG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron MP110TG in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron MP110TG

Elkron MP110TG User Manual - German - 32 pages

Elkron MP110TG User Manual - French - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info