Manual Elkron MP110TG (page 4 of 20) (English)

741485

Zoom out

Zoom in

1/20

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

4. To disarm the system, insert the key and remove it when the leds go

OFF.

Recognition of Key with Masked System

• When the system is masked, all the commutator leds are OFF.In this

way it is impossible to know whether the system is armed and masked

or actually turned OFF.

• The insertion of a key with valid code causes all four commutator leds

to light up for 0.5s. This indicates that the key code has been correctly

readand is followed by the display of system mode for 3.5 seconds.

• Removal of the key before this time has expired causes the system to

return to the masked mode; leaving the key inserted enables a change

in system mode like the one that took place with the arming/disarming

procedure by electronic key.

• While the commutators always mask system mode, the keypads only

perform masking if the unit is armed. When OFF, all data is visible as

if the system were unmasked.

Code Recognition with Masked System

• With masked system, all keypad leds are off, except for the mains led.

In this way it is not possible to know whether the system is armed and

masked or it is really off.

• By entering a valid code the keypad being used visualizes the plant

status for one minute: within this period it is possible to operate.

• After 1 minute from the introduction of the code, the system is masked

again.

2.Access Codes

• The unit can be programmed so as to enable User 2 (e.g., service

personnel, custodian, porter , telemonitoring, private vigilance, etc)

to have his own secret access code which allows him to arm/disarm

the unit without performing other operations.

• The unit identifies up to a maximum of 8 different assigned codes and

as many users:

• After entering a correct code that is enabled, the unit’s buzzer beeps

twice, or it beeps once at length to indicate an error. The Master user’s

code is always enabled; the other codes must instead be enabled (refer

to par. “Code Enabling”).

• If the engineer’s code is enabled, it remains enabled until the Master

user’s code is again entered to partially or totally arm the system, or

until the first arming by electronic key-

• Once armed, every re-entry/EXCLUDED display procedure triggers a

1-minute delay (that is reset each time the key is pressed). If a delay

time-out occurs, the procedure is exited automatically without saving

the changes made.

• The pressing of each key whileentering the secret code causes an

asterisk to be displayed.

FACTORY

CODE

CODE 1 - MASTER USER 1 11111

CODE 2 - USER 2 2 22222

CODE 3 - ENGINEER 3 33333

CODE 4 - TELEMONITORING 4 44444

CODE 5 - USER 5 5 55555

CODE 6 - USER 6 6 66666

CODE 7 - USER 7 7 77777

CODE 8 - USER 8 8 88888

Each user is assigned and “identification

number “ (from 1 to 8) that is to be typed in

before the code; this number allows the unit to

identify the user of the system. To be identified

by the system, the owner must type in the

number 1 followed by his personal code; any

other users will instead type in the number 2,

3, 4, 5, 6, 7 or 8, followed by his personal code

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elkron MP110TG in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron MP110TG

Elkron MP110TG User Manual - German - 32 pages

Elkron MP110TG User Manual - French - 120 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elkron MP110TG Manual

Product: