741484
16
Zoom out
Zoom in
Previous page
1/20
Next page
(((ELKRON)))
MP110 USER MANUAL
(((ELKRON)))
MP110 USER MANUAL
5.
Display of Zones Status
One or more stored alarms are indicated by the flashing of the
.led Stored alarms are displayed by pressing the
A
key;
The number “nn” is displayed, (where nn is the sensor number, refer to
the sensor table to know to which zone it corresponds)
For a display in sequence of the other zones, press the
1
key
consecutively. If the
TOTAL
key is pressed during display, the first zone
on the list is shown again. At the end of the list, the symbol “- -” (two
hyphens) appears on the display.
If the
A
key is pressed when there are no stored alarms, the
message “- -” (two hyphens) will appear on the display.
One or more stored tamperings are indicated by the flashing of the
led. To display these, press the
S
key.
The display will indicate the number: “nn” (where nn is the number
corresponding to the type of tampering that has occurred: see table
below)
5.1 Display of Stored Alarms
5.2 Display of Stored Tamperings
CONTROL UNIT OPENING TAMPER
FALSE CODE
T/A CONTROL UNIT INPUT
WIRE INPUT t/A EXP.1
WIRE INPUTt/A EXP.2
FALSE KEY
SERIAL LINE SABOTING
WIRE INPUT t/A EXP.3
WIRE INPUT t/A EXP.4
EXP.1 OPENING TAMPER
EXP.2 OPENING TAMPER
EXP.3 OPENING TAMPER
EXP.4 OPENING TAMPER
TELEPHONE LINE FAILURE
25
The acknowledgement of a correct code (keypad entry, reading of a key,
or mechanical key arming) immediately stops all alarms thay may be in
progress exception made for the telephone calls.
To lock the communicator (burglary events), it is necessary to disarm the
system from keypad, commutator, or mechanical key. If the communicator
has already started a transmission, the current call is completed and the
following voice calls are cancelled.
12. Lock of Alarm in Progress
The function allows the control unit receiving a telephone telemanagement
call from the engineer (FASTLINK+MODEM) to call back immediately after
checking the safety codes.
NOTE: the transponder function shall be enabled
The function is factory disabled and can be enabled only by the MASTER
USER with two different modes:
- mode A the control unit calls back the first MODEM type number among
the programmed numbers
- mode B the control unit calls back a specific telephone number sent by
FASTLINK
The following procedure is accessed:
1. Enter MASTER USER code
2. Press
F
+
TEL
9
+
ZONE
3
in sequence
3. The display will visualize : call back - 0 - (default value)
4. By means of key
1
it is possible to select:
call back - A - (mode A)
call back - B - (mode B)
5. Press key
F
to confirm and exit from programming
13. Calling Back
16
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron MP110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron MP110 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron MP110

Elkron MP110 User Manual - German - 32 pages

Elkron MP110 User Manual - French - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info