741484

Elkron MP110 Manual

12
Zoom out
Zoom in
Previous page
1/20
Next page
(((ELKRON)))
MP110 USER MANUAL
(((ELKRON)))
MP110 USER MANUAL
1. Enter MASTER code
2. Press keys
EXIT
F
+
TEL
9
+
O
in sequence
3. The display will visualize the two flashing digits corresponding to the
first voice number; by keys
1
and
2
it is possible to go to other
numbers to be programmed.
4. Press key
O
corresponding to the telephone number to be
programmed. The digits will remain on in a fixed mode.
5. Press key
S
: approx. every 1 s. the digits of the first
telephone number are visualized (one digit at a time). For every
visualized digit, the buzzer will beep twice (in case of no programmed
digit, the display will visualize “- - “. Once completed the number
visualization, you go back to point 3).
6. Press key
E
to access the introduction of a new number (the display
will show “n” flashing”). By means of the numeric keys, enter the desired
number. To introduce a pause, enter C** followed by one numeric key
corresponding to the desired length of the pause (see side table).
7. Press key
O
to confirm and save the entered number. The
buzzer beeps twice to confirm operation and you go back to point 3.
8. To cancel a previously programmed telephone number proceed up to
point 4 and then press key
E
followed by key
O
. The
telephone number is cancelled.
9. Press key
EXIT
F
twice to exit from programming.
8.Telephone Number Programming
AVAILABLE PAUSES
C
**
, 1 = 1sec. ---->
C
**
, 5 = 5sec. ---->
C
**
, 9 = 9sec. ---->
9. Telephone Line Test
1. Enter MASTER code +
F
+
9
+
3
.
2. The keypad display will visualize symbol (on in fixed mode).
3. Press key
3
to start procedure.
The keypad display will visualize the following message:
(flashing).
4. At the end of the test, you go back to the main menu of the
communicator parameters.
5. Press key
EXIT
F
to exit.
29
6.Clock Setting
1- Enter MASTER code
2- Press in sequence
F
and
8
3- The display will show “Prog. Time hh:mm”
4- Enter a value between 00 and 23 ( 2 digits required)
5- Enter a value between 00 and 59 ( 2 digits required)
• To confirm and store the entered time, press key
F
• Before storing the entered time, the entered data are controlled. In case
of inconsistency, an error beep is generated and you go back to point
3. In case of correct data, the new time is stored and the positive result
of the operation is confirmed by an OK beep. When quitting by timeout,
the modification is not saved.
6.2 Date Modification
1- Enter MASTER code
2- Press in sequence
F
and
5
3- The display will show “PRG DATE dd-mm-yy”
4- By means of the numeric keys enter the date of the desired day (2 digits
from 0 to 31).
5- Enter a value from 01 to 12 (2 digits) corresponding to the desired month.
6- Enter a value from 00 to 99 (2 digits), corresponding to the desired year.
7- To confirm and store the entered date, press key
F
.
• The system carries out no control on the consistency of the entered
data; the operator shall therefore ascertain that the programmed day/
month data are correct before confirming. When quitting by timeout, the
modification is not saved.
6.1 Hours/Minutes Modification
12
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron MP110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron MP110 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron MP110

Elkron MP110 User Manual - German - 32 pages

Elkron MP110 User Manual - French - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info