741400

Elkron IT500CLOUD Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
6 IT500CLOUD
BUS CONNECTION
WARNING! Always connect and disconnect the devices to the bus with the control panel not
powered (mains and battery disconnected).
Refer to the installation manual of MP500/8 control panel with regard to the cable section,
distances and extensions.
Wires with cross-section area of 0.5 mm² or larger must comply with IEC 60332-1-2; wires
with cross-section area smaller than 0.5 mm² must comply with IEC 60332-2-2.
Connect the device to the BUS using terminals +, +D, D and ─ (Legend Fig. 1 - E and Fig.3)
The device can be connected to the BUS in cascade, star or mixed mode.
The total length of all bus stretches must not exceed 400 m.
CONFIGURATION
After having positioned and wired the device to the bus of the control unit (operation to be
performed with the control unit not powered) proceed with:
Device acquisition on the bus
Proceed as follows to perform the acquisition procedure:
1. Enter in the acquisition mode from keypad MP500/8 control panel, by typing > Code > Technical
>OK.
2. Press the programming button “PROG” when the message "Acquisition in progress" appears
on the display (see Legend Fig.1 - A),
3. The keypad buzzer sounds and the "Acquisition in progress" message disappears.
4. The LED on the board blink quickly three times to indicate that the address has been acquired.
5. Then, the LED starts blinking in Access Point mode with normal operation.
During normal operation, by pressing the programming button “PROG” (see Legend Fig.1 - A), the
board runs a short LED sequence, which specifies the address acquired.
The IT500CLOUD interface board being acquired, is recognised by the MP500/8 control
panel as a keypad and the first available address is assigned to it. Pay attention to the number of
keypads already present in the system. The maximum number allowed is 8 (e.g. if a board is
acquired there may be up to 7 keypads in the system).
Device network parameter configuration
The device can work both either with Ethernet network or with WiFi using your home network or
one available in DHCP mode. By default, the device is in "Access Point" mode, it will be
necessary to define the operating mode through the “My Elkron Family” App.
NOTE: If the Ethernet connection is used, this mode can be enabled directly, following the
instructions below:
• When the interface is operating (two blink every 8 seconds) press the “PROG” button 5 times”.
• After the command wait a few moments (about 20 seconds), the interface restarts and goes into
the chosen mode (Ethernet).
• Power off the interface, wait 10 seconds, and power up the interface again.
Proceed as follows to configure:
Power the control unit, if you have chosen to connect it to your home network via cable (Ethernet),
connect it to the connector on the device (see legend Fig. 1 - F).
Start the My Elkron Family application previously installed and proceed as follows:
• Press the “Other” button.
• Select the "Add Device" menu.
• Follow the instructions which will appear on the guided menu.
If all the parameters were programmed correctly, the device is ready to be managed via the My
Elkron Family App.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron IT500CLOUD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron IT500CLOUD in the language / languages: English, French, Italian as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info