741416
10
Zoom out
Zoom in
Previous page
1/22
Next page
10 DS80HP8A-001F
<
<
N
N
O
O
T
T
E
E
>
>
If 5 short beeps are heard when arming/disarming, it means that the Tamper switch was not completely pressed. Make
sure that the Tamper switch is set correctly and then repeat the control unit check.
Replacing the batteries
Step 1: Deactivate the tamper function on the control unit. If the siren is installed on MP500/xx, access “Maintenance
mode (see the instruction manual of the control unit for details). The siren will generate an acoustic signal to
indicate that the Tamper switch is off.
Step 2: Remove the cover fixing screw on the bottom and carefully extract the external container.
Step 3: Remove the LED cover by loosening the two screws which fix it.
Step 4: Move the power switch to the OFF position.
Step 5: The battery housing is a large size compartment with a cover fixed by means of four screws. Remove the four
screws and remove the cover from the housing.
Step 6: Remove the flat batteries and press the Tamper switch twice to discharge the device.
Step 7: Insert new batteries in the battery housing.
Step 8: After having inserted all the batteries, move the power switch to terminal BT4. All the LEDs will blink once and the
buzzer will beep once.
Step 9: Reposition the LED cover and fix it with two screws.
Step 10: Reposition the battery housing cover and fix it with four screws. Be careful not to tighten the screws excessively.
Step 11: Reposition the upper cover by coupling it to the top of the base. Press the bottom of the upper cover onto the base
and tighten the screw of the bottom.
Step 12: Reactivate the tamper function on the control unit. If the siren is installed on MP500/xx, exit “Maintenance” mode
(see the instruction manual of the control unit for details).
Step 13: After replacing the batteries, the low battery indication disappears from the portal and app after the first Supervision
or in case of opening of the tamper switch after reactivating it. If Supervision is disabled or the tamper switch is not
opened after the expected time of one hour, the low battery indication will not disappear from the portal and app.
For this reason, Supervision must be enabled on the control unit.
Tamper switch
pin to be pressed
completely
against the wall
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron HP600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron HP600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron HP600

Elkron HP600 Quick start guide - English, German, French, Italian - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info