741416
7
Zoom out
Zoom in
Previous page
1/16
Next page
Step 2: Reposition the upper cover by coupling it to the top of the base. Press the bottom of the upper cover onto the
base and tighten the screw of the bottom.
Step 3: Reactivate the tamper function on the control unit. If the siren is installed on MP500/xx, exit “Maintenance
mode (see the instruction manual of the control unit for details).
<NOTE>
If 5 short beeps are heard when arming/disarming, it means that the Tamper switch was not completely pressed.
Make sure that the Tamper switch is set correctly and then repeat the control unit check.
Restoring default settings
The siren settings can be reset and cleared from memory by means of the following procedure:
Step 1: Deactivate the tamper function on the control unit. If the siren is installed on MP500/xx, access “Maintenance
mode (see the instruction manual of the control unit for details). The siren will generate an acoustic signal to
indicate that the Tamper switch is off.
Step 2: Remove the siren from the list of device of the control unit (see the instruction manual of the control unit).
Step 3: Remove the screw from the bottom of the upper cover and remove the upper cover.
Step 4: Remove the LED cover by loosening the two screws which fix it.
Step 5: Move the power switch to the OFF terminal and insert the batteries in the battery housing.
Step 6: Hold the learn/test button pressed for 3 seconds and move the power switch to BT4. The LED groups will blink
in sequence and the siren will beep.
Step 7: Release the learning/test button when the beep is heard. The old parameters of the siren will be deleted and
it will return to normal mode.
Step 8: Reposition the LED cover and fix it with two screws.
Step 9: Reposition the battery housing cover and fix it with four screws. Be careful not to tighten the screws
excessively.
Step 10: Reposition the upper cover by coupling it to the top of the base. Press the bottom of the upper cover onto the
base and tighten the screw of the bottom.
Step 11: The siren can be learnt again at this point with default settings.
<NOTE>
If the siren is installed on MP500/xx, it must be deleted from the device light (see the instruction manual of the control
unit for details).
<NOTE>
If you want to run the learning procedure of the detector again on a control unit after a factory reset, follow all the steps
listed in the “Learning procedure” paragraph again, starting from extracting the batteries from their housing.
Tamper switch
pin to be pressed
completely
against the wall
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron HP600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron HP600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron HP600

Elkron HP600 User Manual - English, German, French, Italian - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info