741416

Elkron HP600 Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
The functions of each Dip Switch of the functional switch block are shown below:
SW1 Reserved
SW2 Light alarm activation (LED groups 1-2-3)
OFF position
Only during the acoustic alarm (
default
)
ON Until the system is deactivated
SW3 SW4 Alarm time
OFF position OFF position
3 minutes (
default
)
OFF position ON 5 minutes
ON
OFF position
10 minutes
ON
ON
1 second (sounded TEST use)
SW5 SW6 Volume control: siren sound, exit/entrance confirmation/delay sound
OFF position OFF position Reserved
OFF position ON Down
ON OFF position Medium
ON
ON
High (
default
)
SW7 Chime function (not managed on MP500/xx systems)
OFF position
Off (
default
)
ON On
Siren configuration
Learning procedure
Step 1: Remove the screw from the bottom of the siren and remove the upper
cover.
Step 2: Undo the two screws fixing the LED cover and remove the LED cover.
Step 3: Set the control unit to learning mode; see the instruction manual of the
control unit for details.
Step 4: Power the siren (switch on BT4) . All the LEDs will blink once and the
buzzer will beep once.
Step 5: Press and release (1 second) the LEARN button. The siren will beep once
and the LED groups 1 and 3 will light up for a short time. Now the siren is
in learning mode and will transmit to the control unit.
Step 6: If the control unit has not received a learning code, press and release (1
second) the LEARN button again (the siren will not sound this time).
<
<
N
N
O
O
T
T
E
E
>
>
On MP500/xx, in case of learning failure, cancel the siren (e.g. HP01) from the control unit (for
details, refer to the manual of control unit instructions), before attempting again.
Step 7: If the control unit receives the learning code, will be sent to the siren a
confirmation message. After having received the confirmation message, the
siren will emit a short duration beep and the LED group 2 will blink once to
indicate that the learning process was successful. At that point, the siren will
exit learning mode.
<NOTE>
If the siren does not receive the confirmation code from the control unit within one minute, the siren will exit learning
mode and the LED groups 1 and 3 will be switched off.
Walk Test
Proceed with the Walk Test and installation after having concluded the learning operation.
Step 1: Deactivate the tamper function on the control unit (EGON). If the siren is installed on MP500/xx, access
“Maintenance” mode (see the instruction manual of the control unit for details). The siren will generate an
acoustic signal to indicate that you are in Maintenance mode / Tamper switch off.
<NOTE>
The Tamper function will remain OFF for one hour. The control unit will return the function automatically back
to ON after this period of time.
Step 2: Find the point where to install the siren.
Step 3: Remove the upper cover by removing the screw on the bottom and carefully extracting the external container.
Step 4: Remove the LED cover by loosening the two screws which fix it.
Step 5: Check the radio connection level by setting the control unit in Walk Test mode and pressing the learn button.
Step 6: If the test is successful, position the LED cover and fix it with two screws.
Installation
Step 1: Identify the four mounting holes, install and fix the siren to the wall using the large screws and the anchor
bolts provided. Tighten the screws and make sure that the Tamper switch is fully pressed against the wall. If
there is a gap, fill it with suitable spacer material.
Lower screw
Upper cover
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron HP600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron HP600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron HP600

Elkron HP600 User Manual - English, German, French, Italian - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info