Manual Elite Drivo (page 43 of 127) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

782410

Zoom out

Zoom in

1/127

in use: push the safety lever (Pic. 24) and fold the front leg

(Pic. 25).

- It’s also possible to rotate the front foot by 90° (Pic. 26)

to fold the hometrainer more compactly after training. In

this case, the hometrainer must be stored horizontally as

indicated (Pic. 27) to prevent it falling and becoming da-

maged.

NOTE: For more stability place the feet (H) in the 28 ROAD

position as in (Pic. 28).

- Drivo can be stored vertically by leaning on the floor as

indicated (Pic.29), but make sure the front leaning area in

contact with the floor is rotated as indicated (Pic. 30). Be

aware that the flywheel of the hometrainer is moved up hi-

gher in this position, so any external bumps or oscillations

might cause it to fall down. The folded up hometrainer

must always be placed close to a wall that might break its

fall.

NOTE: Before storing the hometrainer in this manner,

make sure it’s safely folded up by moving its upper handle.

RECOMMENDATIONS FOR USE

Choose a cassette range that is compatible with your goals

and fitness level:

1) cassettes with a range of 11 to 23/25 teeth are recom-

mended for professional athletes and amateurs who are

able to develop high power output.

2) Cassettes with a greater number of teeth, such as 12/

13 to 27 /29, are recommended for all other cyclists.

- Derailleurs should work properly after bicycle installation

on Drivo. Occasionally, an adjustment may be necessary

for proper operation. If you have any questions, please

contact your dealer to ensure proper derailleur operation

with Drivo.

INSTRUCTIONS ON HOW TO INSTALL THE

FREEHUB WITH CAMPAGNOLO® 9/10/11

SPEED SPROCKET CASSETTES

- To replace the original freehub body installed on Drivo

with the accessory body compatible with Campagnolo®

9/10/11 speed cassettes, follow the procedure below:

1) Unscrew the adapter on the cogset shaft (Pic. 31).

2) Remove the freehub body from the Drivo shaft (Pic. 32).

3) Fully insert the Campagnolo® cassette compatible

freehub body (Pic. 33-34).

4) Tighten the cog set shaft adapter using a 5 mm hex

wrench to a torque of 5 Nm (44in-lbs). Use a medium-

strength oil tolerant threadlocker to lock the adapter on

the shaft.

- You can now mount your Campagnolo® 9/10/11 speed

cassette onto the freehub body without using the spacers

(Ref. E) (Pic. 35) (only for 11 speeds).

ATTENTION!

Strictly follow the instructions provided by the cassette ma-

nufacturer with regard to specific installation techniques,

the need for additional spacers and torque specifications.

NOTE: Please contact your dealer if you have questions

about installation or if you cannot install the cassette. The

warranty does not cover any DAMAGE to the bicycle and/

or Drivo in the event of incorrect installation.

MAINTENANCE

Drivo does not require any specific scheduled maintenan-

ce, however the following precautions are recommended:

- wipe the trainer clean with a cloth after each training

session to prevent the accumulation of dust and sweat;

- Do not clean or degrease the bicycle chain while the bike

is mounted on Drivo as solvents can cause irreparable da-

mage to the bearings or other internal mechanical parts;

- Check that the quick release is properly secured and fully

working before every training session.

WARNING: The tension of the internal transmission belt is

tested on every product by Elite’s assembly department;

do not alter belt tension as the power sensor must be re-

calibrated with every variation in belt tension.

- The belt tension may lessen after multiple uses or after

particularly intensive training sessions, and as a conse-

quence, the accuracy of the transmission of the user po-

wer output may reduced. If that’s the case, you might need

to increase the transmission belt tension by the following

method:

1) Remove the motherboard cover (Pic. 36).

2) loosen the adjustment locking screw by one full turn, so

that you can then turn the adjusting nut (Pic. 37).

3) Turn the adjusting nut half a turn to tighten the belt

correctly (Pic. 38).

4) Begin the calibration procedure as indicated in para-

graph 37.

5) Repeat the previous operation if data transmission still

not correct.

6) Once calibration is done replace the motherboard cover

(Pic. 39).

WARNING!: Make sure the re-tensioning procedure has

been pre-approved by Elite’s tech assistance department

before re-tensioning the belt (Pic. 40). Breaking the anti-

tampering seal invalidates the product’s warranty.

WARNING

- Drivo becomes hot during use. Wait for it to cool before

touching the resistance unit covers.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elite Drivo in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elite Drivo Manual

Product: