Manual Elica Ye (page 28 of 136) (All languages)

649836

Zoom out

Zoom in

1/136

colouring agents on CRISTALPLANT

, surface; the

same may occur as for lit cigarettes; but all of that can be

removed following the recommendations reported below.

HOW TO REMOVE PERSISTENT STAINS,

SCRATCHES AND BURNING RINGS

CRISTALPLANT

is an homogeneous material in all its

thickness and depth, thus it can restore its surface

original beauty from aggressive agents, such as

scratches, burning rings from cigarettes and persistent

stains, simply by following these instructions: as for small

damages, use an abrasive Scotch Brite© (3M trademark)

sponge and a common abrasive detergent to restore the

surface. Rub superficially the damaged part down. If the

defect is still visible, rub again using very fine glass-

paper.

TO USE:

Powder or cream detergents (like CIF©, VIM© or similar),

containing micro-granules with abrasive action on the

surface. Methylated spirits may be used only being wary

of rinsing well the surface.

NON TO USE:

Solvent agents like acetone or trichloroethylene, as well

as other aggressive chemical substances like strong

acids (muriatic acid…) or bases (caustic soda…).

Detergents for industrial use or others of unknown

aggressive action: in this case a test on a spot not in view

should be done before application. Very aggressive

substance generally used to clear sink pipes. Solvents

used in the painting industry.

Maintenance of the parts in glass, steel, plastic and all

materials other than CRISTALPLANT

For cleaning, use a cloth moistened with neutral liquid

detergent.

Avoid the use of abrasive products. DO NOT USE

ALCOHOL!

Warning: Failure to follow the rules of cleaning the unit and

replacing the filters may cause fire. It is therefore

recommended to follow these instructions.

We accept no responsibility for any damage to the motor or

fire damage linked to inappropriate maintenance or failure to

comply with the above mentioned warnings.

Grease filter

Fig. 20-22

Traps cooking grease particles.

This must be cleaned at least once a month (or when the filter

saturation indication system - envisaged on the model in

possession - indicates this necessity), using non-aggressive

detergents, in a dishwasher, which must be set to a low

temperature and a short cycle (Tmax: 70°C).

When washed in a dishwasher, metal parts may discolour

slightly.

The filter must be dried in an oven for one hour at a max

temperature of 100°C; if the filter is still moist, repeat the

operation.

Replace the filter at least every 2 years.

Charcoal filter (filter version only)

Fig. 19

It absorbs unpleasant odours caused by cooking.

The charcoal filter can be washed once every two months

using hot water and a suitable detergent, or in a dishwasher at

65°C (if the dishwasher is used, select the full cycle function

and leave dishes out).

Eliminate excess water without damaging the filter, then put it

in the oven for 10 minutes at 100° C to dry completely.

Replace the mattress every 3 years and when the cloth is

damaged.

Replacing lamps

Fig. 21

Disconnect the appliance from the electricity.

The hood is equipped with a lighting system based on LED

technology.

The LEDs guarantee an optimum lighting, a duration up to 10

times as long as the traditional lamps and allow to save 90%

electrical energy.

To purchase spare LEDs, contact the technical assistance

service.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elica Ye in the language / languages: All languages as an attachment in your email.

The manual is 3,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elica Ye Manual

Product: