340838
5
Zoom out
Zoom in
Previous page
1/86
Next page
3. Cleaning
Clean the refrigerator thoroughly at intervals, as
necessary. Remove the shelves; these, the cabinet
interior and the door should be washed with a warm
solution of sodium bi-carbonate. Finally wipe over
with a cloth rinsed in warm water only, and dry with
a clean cloth. Do not wash any plastic parts in water
that is more than hand warm, and do not expose
them to dry heat. The outside of the cabinet should
be wiped down regularly with a clean, damp cloth.
NEVER USE STRONG CHEMICALS OR ABRASIVE
CLEANING MATERIALS ON ANY PART OF THE
CABINET.
4. Positioning the appliance
When first using this refrigerator please consider
the following points:
ENSURE REFRIGERATOR IS LEVEL
THE PIPEWORK AT THE BACK GETS HOT IN
USE
THE REFRIGERATOR HAS NO ‘MOTOR’ AND
IS THEREFORE VIRTUALLY SILENT
ALLOW AT LEAST 3 HRS. FOR SIGNS OF
COOLING
During the refrigeration process, the appliance gives
off heat from the condenser (under the upper part
of the rear cover) into the surrounding air. The more
ventilated the condenser is, the more effective the
refrigeration will be.
The other condition for satisfactory operation is
that the appliance is levelled. This could be
checked by placing
a glass of water on top of the
appliance.
It is important that the appliance is not directly
exposed to radiated heat (sunlight, radiator, near
an oven, etc.).
4.1. Installation instructions
The refrigerator is equipped with an electrically
heated absorption cooling unit which is virtually silent
in operation. The fridge is designed for free-standing
installation, but can be built-in if the following
conditions are complied with to ensure satisfactory
operation and maximum cooling efficiency.
IMPORTANT
Please follow the installation details below
carefully. Guarantee is valid for products
installed as described only.
1. The refrigerator must be
level both directions
2. There should be
20mm clearance to the wall
3. Ventilation must be provided
as shown in
alternatives A, B, C or D (fig 2-3)
4. The ventilation duct must at least measure
105mm x the width of the refrigerator
5.
Only the entire cooling unit must project into
the duct as shown
6.
Air passing through the duct must not be
5
GB
7. Ventilation grills, if used, must have an free
openings of
at least 200cm2 each
During installation, please ensure the mains
plug is accessible at all times.
5. Using the appliance
To start the refrigerator connect the plug into a
properly earthed socket.
The cooling fins should show signs of cooling
after about 3 hours. The refrigerator needs about
6 hours at normal ambient temperature to reach 6
°C in the storage compartment.
5.1. Temperature regulation
The usual setting required is in the region of 2 to 3 on
the thermostat knob (Fig. 4), but this can vary with
Figure 2.
Figure 3.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Electrolux ea 3120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Electrolux ea 3120 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info