561013
13
Zoom out
Zoom in
Previous page
1/36
Next page
Operating controls and connecting terminals
13
1. SUBWOOFER LEVEL
The subwoofer volume control should be adjusted to match the main speaker volume of your hifi or home
cinema system. As a general rule, subwoofer performance should not dominate the sound. Excessive
bass leads to a smeared soundstage and can result in unpleasant resonances at certain frequencies.
2. LOW-PASS CROSSOVER
Used to adjust the frequency at which the subwoofer crosses over. Signals above this crossover fre-
quency are gradually rolled off so they do not interfere with the main speakers. The adjustment of the
crossover frequency will depend on the size and frequency response of the main loudspeakers.
Loudspeaker configuration Crossover frequency
Home cinema set (5.1 …) with LFE channel 120 - 160 Hz
Hifi/Stereo system with very small loudspeak-
ers
80 - 120 Hz
Stereo system with satellites and subwoofer
(2.1)
80 - 120 Hz
Hifi/Stereo system with medium-sized book-
shelf speakers, smaller floor standing loud-
speakers (compatible with most ELAC loud-
speakers)
50 - 80 Hz
3. POWER
Provided on the rear of the subwoofer, there are three positions available:
AUTO: Normal position. The ELAC subwoofer is switched to standby mode (indicator light LED glows
red).
A sensor controls the inputs. If the appropriate bass signal is present, the power output stage is switched
on. Within tenth of a second, the subwoofer is ready for operation (indicator light LED glows green). The
subwoofer switches into standby mode again after a signal pause of more than 15 minutes (indicator light
LED glows red).
Note: If the automatic turn-on operation only responds to full volume, please increase the bass/LFE level
of your surround receiver and decrease the subwoofer level about the same amount. This way, there will
not be any changes in acoustical bass level and the subwoofer will be turned on automatically at a lower
volume.
ON: The subwoofer is operating continuously (indicator light LED glows green).
OFF: The subwoofer is held in standby mode continuously (indicator light LED glows red).
To switch off the subwoofer completely, please switch the MODE control to OFF. A second later, the
Power switch can be turned off without any noise.
4. LED
ON / Standby LED. Glows green when device is switched on; glows red when device is in standby mode.
5. PHASE
The acoustical phase relative to the input phase may be adjusted by means of the phase control knob.
The range is (in phase) to 180° (out of phase). The optimum adjustment should be determined within
the listening test. While going through the whole range of the phase control adjuster, the adjustment with
the highest bass output at the listening place should be kept.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elac SUB 2025 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elac SUB 2025 in the language / languages: English, German as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info