606717

Einhell TH-RO 1100 E Manual

23
Zoom out
Zoom in
Previous page
1/112
Next page
GB
- 23 -
6. Operation
•
Never use a low quality or damaged cutter.
Use only cutting tools with a shaft diameter of
6 mm or 8 mm. The cutters must also be desi-
gned for the appropriate idling speed.
•
Secure the workpiece so that it cannot be
thrown through the air as you work on it. Use
clamps or a vise.
•
Always guide the power cable away from the
back of the tool.
•
Never cut over metal parts, screws, nails etc.
6.1 ON/OFF switch (Fig. 12/Item 4)
Press the safety lock-off (5) and then press the
ON/OFF switch (4) to switch on the machine.
Release the ON/OFF switch (4) to switch off the
machine.
6.2 Speed control (Fig. 13 – Item 11)
The best speed depends on the material and the
diameter of the cutter. Select a speed between
11,000 and 30,000 rpm using the speed control
switch (11). You can choose from 7 diff erent
switch positions. The speeds in the various switch
positions are as follows:
Switch position 1: approx. 11,000 rpm
(minimum speed)
Switch position 2: approx. 12,000 rpm
Switch position 3: approx. 15,000 rpm
Switch position 4: approx. 18,000 rpm
Switch position 5: approx. 22,000 rpm
Switch position 6: approx. 26,000 rpm
Switch position 7: approx. 30,000 rpm
(maximum speed)
To increase the speed:
Move the speed control switch (11) in the plus
direction.
To reduce the speed:
Move the speed control switch (11) in the minus
direction.
6.3 Adjusting the routing depth (Fig. 14 – 17)
•
Place the machine on the workpiece.
•
Undo the wing screw (16) and fixing handle
(9).
•
Slowly move the machine downwards until
the cutter makes contact with the workpiece.
•
Tighten the fixing handle (9).
•
Set the fine adjuster (15) to 0 as shown in Fig.
17.
•
Adjust the revolver end stop (14) so that the
depth stop (19) is above the end stop (a) set
to the lowest height.
•
Lower the depth stop (19) until it touches the
end stop (a). Then tighten the wing screw
(16).
•
Set the pointer (17) to the zero point on the
scale (18).
•
Undo the wing screw (16). Push the depth
stop (19) upwards until the pointer (17) points
at the required cutting depth on the scale
(18). Tighten the wing screw again.
•
Test the setting by completing a test cut on a
waste piece.
•
Now you can carry out the final adjustment
of the cutting depth. To do this turn the fine
adjuster (15) to the required dimension.
Turn the fi ne adjuster (15) counter-clockwise: gre-
ater cutting depth
Turn the fi ne adjuster (15) clockwise: lower cutting
depth
Turning the fi ne adjuster (15) through one division
corresponds to a change of cutting depth of 0.04
mm, one whole turn corresponds to 1 mm.
On the precision adjustment device (15) you
can also turn the lower ring (b) separately. This
lets you reach the zero point without altering the
precision adjustment device (15). See Fig. 17 and
proceed as follows:
•
Press down the ring (b).
•
Hold and turn it until you have reached the
desired position.
•
Release the ring again.
Anl_TH_RO_1100_E_SPK1.indb 23Anl_TH_RO_1100_E_SPK1.indb 23 29.06.12 10:4629.06.12 10:46
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell TH-RO 1100 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TH-RO 1100 E in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 2,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell TH-RO 1100 E

Einhell TH-RO 1100 E User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info