Manual Einhell TH-RO 1100 E (page 22 of 112) (English, Danish, Swedish, Norwegian)

606717

Zoom out

Zoom in

1/112

- 22 -

material. Use a special vacuum cleaner if you

are handling harmful materials.

•

Secure the extraction port (1) to the routing

shoe (2) using the two countersunk screws

(f).

•

The extraction port can be connected to ext-

ractor units (vacuum cleaners) with a suction

hose.

•

The internal diameter of the suction port is 35

mm. Now fit a suction hose of the appropriate

size to the suction port.

5.2 Safety guard port assembly

(Fig. 3/Item 24)

Fit the safety guard (24) as shown in Fig. 3.

5.3 Parallel stop assembly (Fig. 4/Item 21)

•

Push the guide shafts (a) of the parallel stop

(21) into the holes (b) on the routing shoe (2).

•

Set the parallel stop (21) to the required di-

mension and secure it in place with the wing

screws (3).

5.4 Fitting the compass point (Fig. 5)

•

You can route circular areas using the com-

pass point (13) and the mounting to go with it.

•

Clamp the compass point (13) to the end of

one of the guide rods (a). Push the guide rod

(a) into a hole (b) on the routing shoe (2). Se-

cure the guide rod (a) on the routing shoe (2)

using the securing screws (3).

•

Set the required radius between the compass

point (13) and cutter.

•

Position the compass point (13) in the center

of the circle you wish to route. If necessary

undo the wing screw (c) on the compass

point (13) and extend/shorten the part of the

compass point (13) that points downwards.

5.5 Guide sleeve assembly (Fig. 6-7/Item 20)

•

Secure the guide sleeve (20) to the routing

shoe (2) using the two countersunk screws

(f).

•

The guide sleeve (20) is guided along the

template (c) using the guide ring (b).

•

The workpiece (d) must be larger by the diffe-

rence of “external edge of guide ring” and “ex-

ternal edge of router” (e) to obtain a precise

copy.

5.6 Fitting / Removing the cutting tool

(Fig. 8-11)

 Important. Pull out the power plug ﬁ rst.

 Important. After working with the router,

the cutting tool will remain very hot for a rela-

tively long time.

 Important. Cutters are very sharp. Wear

protective gloves at all times when handling

cutting tools.

•

Cutters with a shaft diameter of 6 mm and 8

mm may be fitted to this router. Most cutters

are available in both sizes.

•

You can use cutters made of the following

materials:

- HSS - suitable for cutting softwood

- TCT - suitable for cutting hardwood, particle

board and plastic.

•

Select the appropriate cutting tool for the job

in hand.

•

When using the cutters for the first time: Re-

move the plastic packaging from the cutter

heads.

•

Clean the nut, clamp and shaft of the cutter

before fitting it.

•

Press the spindle lock (12) and allow the

spindle to engage by turning it at the same

time.

•

Undo the clamp nut (10) using the open-

ended spanner (22).

•

If necessary take the cutter you wish to remo-

ve out of the clamp (23).

•

Select the appropriate cutting tool for the job

in hand.

•

Select the appropriate clamp for the cutter

(23).

•

Now fit the clamp (23) and nut (10) into the

cutting spindle.

•

Guide the cutter shaft into the clamp.

•

Press and hold the spindle lock (12).

•

Tighten the clamp nut (10) using the open-

ended spanner (22).

•

The cutter must be inserted at least 20 mm

into the clamp (23).

•

Before you start the electric router, check to

ensure that the cutting tool is secure and runs

smoothly.

 Important. Remove the setting and assem-

bly tools before starting the machine

Anl_TH_RO_1100_E_SPK1.indb 22Anl_TH_RO_1100_E_SPK1.indb 22 29.06.12 10:4629.06.12 10:46

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TH-RO 1100 E in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 2,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell TH-RO 1100 E

Einhell TH-RO 1100 E User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 76 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell TH-RO 1100 E Manual

Product: