Manual Einhell TE-CD 18-2 i (page 21 of 100) (English, German, Dutch, French, Italian, Portuguese, Spanish, Finnish)

606110

Zoom out

Zoom in

1/100

- 21 -

6.4 Changeover switch (Fig. 5/Item 3)

The slide switch above the On/Oﬀ switch is for

setting the direction of rotation of the cordless

screwdriver and for preventing the cordless

screwdriver from being switched on inadvertently.

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to

the gearing, the direction of rotation must only be

changed when the screwdriver is at a standstill.

When the slide switch is in the middle position,

the On/Oﬀ switch is blocked.

6.5 On/Oﬀ switch (Fig. 5 / Item 4)

Inﬁ nitely variable speed control is possible with

the On/Oﬀ switch. The further you press the

switch, the higher the speed of the battery-powe-

red drill/screwdriver.

6.6 Changing over from 1st gear to 2nd gear

(Fig. 6 / Item 7)

You can work at a higher or lower speed depen-

ding on the position of the selector switch. To avo-

id damaging the gear unit you should only change

over gears when the tool has stopped.

6.7 LED display for clockwise/counter-clock-

wise operation (Figure 6/Item 11)

The LED display for counter-clockwise/clockwise

(11) indicates the position of the changeover

switch (3).

Green LED (11a) is lit: clockwise

Red LED (11b) is lit: counter-clockwise

6.8 Battery capacity indicator (Fig. 7 – Item 2)

Press the battery capacity indicator switch (a).

The battery capacity indicator (2) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED is lit:

The battery is empty, recharge the battery.

6.9 LED lamp (Fig. 7 / Item 10)

The LED lamp (10) can be used in poor lighting

conditions to illuminate the area where you want

to drill or screw. The LED lamp (10) will be lit

automatically as soon as you press the ON/OFF

switch (4).

6.10 Changing the tool (Fig. 8)

Caution! Set the changeover switch (3) to its

center position whenever you carry out any work

(for example changing the tool, maintenance

work, etc.) on the cordless hammer drill/screwdri-

ver.

•

The cordless screwdriver is fitted with a

quick-action chuck (9) with an automatic

spindle stop.

•

Open the chuck (9). The chuck opening (a)

must be large enough to hold the tool (drill bit

or screwdriver bit).

•

Select the suitable tool. Push the tool as far

as possible into the chuck opening (a).

•

Tighten the chuck (9) and then check that the

tool is secure.

6.11 Screwdriving

We recommend using self-centering screws (e.g.

Torx screws, recessed head screws) designed for

reliable working. Be sure to use a bit that matches

the screw in shape and size. Set the torque, as

described elsewhere in these operating instruc-

tions, to suit the size of screw.

6.12 Fitting the additional handle

(Fig. 9/Item 12)

The additional handle (12) enables you to achieve

better stability whilst using the hammer drill. Do

not use the tool without the additional handle.

The additional handle (12) is secured to the ham-

mer drill by a clamp. During the handle clockwise

tightens this clamp. Turning it anti-clockwise will

release the clamp.

•

The supplied additional handle (12) must

first be fitted. To do this, the clamp must be

opened by turning the handle until it is wide

enough for the additional handle to be slid

over the chuck (9) and on to the hammer drill.

•

After you have positioned the additional

handle (12), turn it to the most comfortable

working position for you.

•

Now turn the handle in the opposite direction

again until the additional handle is secure.

•

The additional handle (12) is suitable for both

left-handed and right-handed users.

Anl_TE_CD_18_2_i_SPK7.indb 21Anl_TE_CD_18_2_i_SPK7.indb 21 17.12.13 10:1517.12.13 10:15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TE-CD 18-2 i in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish, Finnish as an attachment in your email.

The manual is 1,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell TE-CD 18-2 i Manual

Product: