Manual Einhell TE-CD 18-2 i (page 20 of 100) (English, German, Dutch, French, Italian, Portuguese, Spanish, Finnish)

606110

Zoom out

Zoom in

1/100

- 20 -

5. Before starting the equipment

Be sure to read the following information before

you use your cordless screwdriver for the ﬁ rst

time:

1. Charge the battery pack with the charger

supplied. An empty battery pack requires a

charging period of approximately 1 hour.

2. Only ever use sharp drill bits and screwdriver

bits which are suitable for the purpose and in

faultless condition.

3. Always check for concealed electric cables

and gas and water pipes when drilling and

screwing in walls.

6. Operation

6.1 Charging the battery (Fig. 2-3)

1. Remove the battery pack (5) from the handle

(Fig. 2) by pressing the pushlock buttons (8)

on the right and left side.

2. Check that your mains voltage is the same

as that marked on the rating plate. Insert the

power plug of the charger (6) into the mains

socket outlet. The green LED will then begin

to shine.

3. Push the battery pack (5) onto the battery

charger. The red LED will blink slowly and the

green LED will shine, indicating that the batte-

ry pack is being charged.

4. Both LEDs will shine when the charging is

completed.

If the green LED and the red LED shine conti-

nuously while the battery pack is inserted, the

charging temperature is either too high or too low.

- In this case, pull out the mains plug of the

charger and charge the battery in an envi-

ronment in which the temperature is either

warmer or colder.

If the red LED blinks quickly and the green LED

shines, the battery pack is too cold or too warm.

- In this case, pull out the mains plug of the

charger and store the battery in a warmer

place or let it cool down and try again.

If the fault still occurs, the battery pack is defec-

tive.

- In this case pull out the charger plug immedi-

ately and remove the defective battery pack.

- Do not use the defective battery pack again.

If the battery pack fails to become charged, ple-

ase check

•

whether there is voltage at the socket-outlet

•

whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please

return

•

the charger

•

the battery pack

to our Customer Service Department.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly.

You must recharge the battery pack when you

notice that the power of the cordless equipment

drops.

6.2 Torque setting (Fig. 4 / Item 1)

Important! The tool must be at a standstill

when you set the torque with the setting ring.

The cordless hammer drill/screwdriver is ﬁ tted

with a mechanical torque selector.

The torque for a speciﬁ c size of screw is selected

with the set-collar (1). The correct torque depends

on several factors:

•

on the type and hardness of material in ques-

tion

•

on the type and length screws used

•

on the requirements needing to be met by the

screwed joint.

The clutch disengages with a grating sound to

indicate when the set torque is reached.

6.3 Drilling/hammer drilling (Fig. 4)

•

For drilling purpose, adjust the torque setting

(1) to the setting “Drill”.

•

For hammer drilling purpose, adjust the

torque setting (1) to the setting “Hammer”.

In the drill and hammer drill settings the slip cou-

pling is non-functional. The maximum torque is

available for drilling and hammer drilling.

Anl_TE_CD_18_2_i_SPK7.indb 20Anl_TE_CD_18_2_i_SPK7.indb 20 17.12.13 10:1517.12.13 10:15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TE-CD 18-2 i in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish, Finnish as an attachment in your email.

The manual is 1,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell TE-CD 18-2 i Manual

Product: