Manual Einhell LE 30 (page 16 of 100) (English, German, Dutch, French, Italian, Portuguese, Spanish)

723951

Zoom out

Zoom in

1/100

- 16 -

4. Fan speed

To choose between a high and a low fan

speed, press the “Fan speed” switch (Fig. 2 /

Item 26).

5. Desired humidity

To adjust the desired humidity setting within

the range of 40% to 80% in 5% increments,

press the “Humidity setting” switch (Fig. 2 /

Item 25) and then press the “Higher/lower”

button (Fig. 2 / Item 24). If the prevailing hu-

midity at the integrated sensor falls below the

desired humidity setting by approx. 2%, the

compressor will stop, followed a little later by

the fan. If the prevailing humidity at the inte-

grated sensor exceeds the desired humidity

setting by approx. 2%, both the fan and the

compressor (3 minute restart inhibit function)

will start up again.

6. Timer

To set the desired operating time (1 – 24

hours) in 1 hour increments, press the switch

for “Timer settings” (Fig. 2 / Item 23) with the

device switched on and then press the “High-

er/lower” button (Fig. 2 / Item 24). If the timer

has not been switched on, the device will run

continuously. If the device is connected to the

voltage supply, press the switch for “Timer

settings” and then press the “Higher/lower”

button (Fig. 2 / Item 24) to set the time, in 1

hour increments, until the device is switched

on (1 – 24 hours).

7. To switch oﬀ , press the On/Oﬀ switch (Fig. 2 /

Item 21).

7. Emptying the condensate

collector

Note:

•

The device switches off automatically when

the condensate collector (Fig. 1 / Item 1) is

full. The „Condensate collector full“ LED will

light up and a warning signal will sound for a

few seconds.

•

If the condensate collector (Fig. 1 / Item 1) is

not refitted correctly after it has been emp-

tied, the “Condensate collector full” LED will

continue to shine.

•

Never remove the “Float” (Fig. 3 / Item A) from

the condensate collector, otherwise the auto-

matic switch-off function will no longer work.

•

If the condensate collector is dirty, you can

clean it with warm water.

1. Remove the condensate collector (Fig. 1 /

Item 1) by pulling it out carefully and then em-

pty it.

2. Slide the collector back into the device after

you have emptied it.

8. Using an external condensate

drain (Fig. 4)

Note:

•

Important: To prevent water damage, make

sure that the condensate is drained away pro-

perly at all times.

•

Important: If the weather is very cold you will

have to take appropriate measures to prevent

the water from freezing in the drainage hose.

•

It is best to direct the condensate into a lower

lying drain. If you use an external collecting

container (e.g. a trough), the equipment must

be positioned accordingly higher.

•

The drainage hose must be installed with a

downward gradient. It must not be kinked or

become clogged.

•

If the drainage hose becomes clogged, the

condensate must run into the condensate

collector from the overflow.

1. Remove the rubber plug and keep it in a safe

place (it must be reinserted in the connection

socket when the external condensate drain is

no longer used).

2. Connect the suction port (B) with a matching

water hose (C) with a 10 mm inside diameter.

De-icing function

To prevent the cooling elements becoming iced

up at operating temperatures below 21°C, the

equipment has a de-icing function. In this case

the compressor is switched oﬀ but the fan motor

continues to run.

During this phase the dehumidifying function is

interrupted for a few minutes.

Please observe the equipment’s operating range

(see Technical Data).

The equipment has a compressor protector which

automatically shuts down the equipment when

the temperature rises above 35°C or falls below

5°C, or when the power consumption rises too

high.

Anl_LE_16_20_30_SPK7.indb 16Anl_LE_16_20_30_SPK7.indb 16 24.02.16 08:3324.02.16 08:33

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell LE 30 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell LE 30 Manual

Product: