782353

Einhell KGS190 Manual

14
Zoom out
Zoom in
Previous page
1/72
Next page
7. Assembly
A.) Adjusting the saw (Fig. 2)
While pressing down lightly on the machine head
(4), pull the lock pin (16) out of the motor holder
to disengage the saw from its bottom working
position.
Swing up the machine head until the retaining
hook latches home.
The machine head (4) can be tilted by max. 45°
to the left by loosening the tensioning screw (13).
Check that the voltage marked on the rating plate
is the same as your mains voltage and connect
up the machine.
B.) Adjusting the stop (Fig. 3)
Disconnect from the mains.
Move the saw head (4) into the 90° position and
tighten the locking screw (10).
Push down the saw head (4).
Place the angle (a) with the long leg against the
stop, as shown in the illustration.
Check whether the saw blade (5) is perpendicular
to the stop (7).
If the position has to be corrected, loosen the two
fixing screws (28) of the stop (7) and adjust the
stop (7) so that it is perpendicular to the saw
blade (5).
Once you have completed the adjustment work,
retighten the two fixing screws (28).
C.) 90° cross-cuts and 0° rotary table (Fig. 4)
Press the main switch (3) to turn on the saw.
Caution! Position the material firmly on the
machine bed so that it cannot move about while it
is being cut.
After switching on the saw, wait for the blade (5)
to reach its maximum speed.
Press the release button (1) and lower the
machine head by its handle (2) smoothly and with
slight pressure down through the workpiece to
make the cut.
When the cut is completed, return the machine to
its top parking position and let go of the On/Off
switch.
Caution! A return spring causes the machine
head to rise automatically at the end of the cut.
Do not let go of the handle (2) as soon as the cut
is completed but steady the machine head and
allow it to rise slowly.
D.) Precision adjustment of the stop for 90°
cross-cuts (Fig. 5/6/9)
Lower the machine head (4) and fix with the
lock pin (16).
Slacken the clamping screw (13).
Place the stop angle (a) between the saw blade
(5) and the rotary table (8).
Slacken the counter nut (29) and adjust the
setting screw (19) until the angle between the
saw blade (5) and the rotary table (8) equals 90°.
Re-tighten the counter nut (29) to fix the machine
in this setting.
E.) 90° cross-cuts and 0°-45° rotary table (Fig. 7)
The KGS 210 can be used to make angled cuts of
0°-45° relative to the stop rail on the left and right
side.
Undo the rotary table (8) by slackening the two
lock screws (19) on the stop rail.
Turn the rotary table (8) by its handle (2) to the
angle you want, i.e. the mark (a) on the rotary
table has to comply with the required angle
dimension (B) on the base plate (9).
Re-tighten the two lock screws (10) to fix the
rotary table (8) in position.
Make the cut as described in Section B.).
F.) Mitre cuts 0°-45° and rotary table 0° (Fig. 5/8)
The KGS 190 can be used to make mitre cuts of
0°-45° relative to the machine bed on the left side.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the clamping screw (13) and tilt the
machine head (4) by its handle (2) to the left until
the arrow (a) on the machine head (4) points to
the required angle dimension (b).
Re-tighten the clamping screw (13) and make the
cut as described in Section C.).
G.) Precision adjustment of the stop for 45° mitre
cuts (Fig. 5/9)
Lower the machine head (4) and fix with the
lock pin (16).
Fix the rotary table (8) in 0° position.
Undo the clamping nut (13) and tilt the machine
head (4) by its handle (2) to an angle of 45° on
the left.
Place the 45° stop angle (c) between the saw
blade (5) and the rotary table (8).
Slacken the counter nut (30) and adjust the
setting screw (18) until the angle between the
saw blade (5) and the rotary table (8) equals
exactly 45°.
GB
14
Anleitung KGS 190 30.10.2001 9:23 Uhr Seite 14
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell KGS190 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell KGS190 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info