Manual Einhell GH-BC 30 AS (page 23 of 136) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

605959

Zoom out

Zoom in

1/136

- 23 -

throttle lever lock (Fig. 1/Item 12) and then

press the throttle lever (Fig. 1/Item 11) and

lock the throttle lever by pressing the lock

(Fig. 1/Item 10) at the same time.

5. Set the choke lever (Fig. 1/Item 5) to „ “.

6. Hold the equipment ﬁ rmly and pull out the

starter cable (Fig. 1/Item 4) until you feel it

start to resist. Then tug sharply on the starter

cable 4 times. The equipment should start.

Important: Never allow the starter cable to

snap back. This may damage the equipment.

Important: Since the throttle lever is secured,

the cutting tool starts to operate when the en-

gine is started.

Then release the throttle lever by actuating

it once. Actuating the throttle lever will also

release the choke lever. (The engine returns

to its idle state).

7. If the engine does not start up, repeat steps

4-6 above.

Please note: If the engine does not start up even

after several attempts, read the section “Engine

Troubleshooting”. Please note: Always pull the

starter cord out in a straight line. If it is pulled out

at an angle, then friction will occur on the eyelet.

As a result of this friction, the cable will become

frayed and will wear away faster. Always hold the

starter handle when the cable retracts. Never

allow the cable to snap back when it has been

pulled out.

7.2 Starting the engine when warm

(The equipment has been idle for less than 15-20

min.)

1. Set the equipment down on a hard, level sur-

face.

2. Switch the ON/OFF switch to “I”.

3. Secure the throttle lever (in the same way as

described in “Starting the engine when cold”).

4. Hold the equipment ﬁ rmly and pull out the

starter cable until you feel it start to resist.

Then tug sharply on the starter cable. The

equipment should start after 1-2 tugs. If the

equipment does not start after 6 pulls, repeat

steps 1 – 7 of the procedure for starting the

engine from cold.

7.3 Switching oﬀ the engine

Emergency Stop procedure:

If it becomes necessary to stop the equipment im-

mediately, set the ON/OFF switch to “Stop” or “0”

Normal procedure:

Let go of the throttle lever and wait until the engi-

ne has changed to idling speed. Then set the ON/

OFF switch to “Stop” or “0”.

7.4 Practical tips

Practice all operating techniques with the engine

switched oﬀ before you start to use the equip-

ment.

8. Working with the petrol power

scythe

Extending the cutting line

Caution! Do not use any kind of metal wire or

metal wire encased in plastic in the line spool.

This may cause serious injuries to the user.

To extend the cutting line, run the engine at full

speed and tap the line spool on the ground. This

will automatically extend the line. The blade on

the safety shield will cut the line to the appropriate

length (Fig. 26).

Important: Remove all grass and weed remnants

at regular intervals to prevent the shaft tube over-

heating. Lawn, grass and weed remnants become

trapped under the safety shield (Fig. 27) and

prevent the shaft tube from receiving adequate

ventilation. Remove the remnants carefully using

a screwdriver or the like.

Diﬀ erent cutting methods

When the equipment is correctly assembled it

will cut weeds and long grass in places which are

diﬃ cult to access, e.g. along fences, walls and

foundations and also around trees. It can also

be used for „mowing“ down vegetation so that a

garden can be better prepared or a certain area

cleared down to the soil.

Please note: Even if it is used carefully, cutting

around foundations, stone or concrete walls, etc.

will result in the line suﬀ ering more than normal

wear.

Anl_GH_BC_30_AS_SPK7.indb 23Anl_GH_BC_30_AS_SPK7.indb 23 16.06.14 11:4216.06.14 11:42

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GH-BC 30 AS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GH-BC 30 AS Manual

Product: