605959

Einhell GH-BC 30 AS Manual

21
Zoom out
Zoom in
Previous page
1/136
Next page
GB
- 21 -
4. Technical data
Engine type .........................................................
........2-stroke engine, air-cooled, chrome cylinder
Engine power (max.) ...................0.8 kW (1.1 HP)
Displacement ........................................30.3 ccm
Idle speed of engine .................3,000 ± 200 min
-1
Max. engine speed..............................8,500 min
-1
Max. torque
Scythe: ...............................................6,375 min
-1
Trimmer: .............................................5,550 min
-1
Ignition .................................................Electronic
Drive ........................................Centrifugal clutch
Weight (with empty tank) ............................6.7 kg
Cutting line diameter (HYP, PA Ø 410) ........41 cm
Cutting circle diameter of blade
(HYP, 65 Mn Ø 230-4T) ...............................23 cm
Cutting line length ......................................... 8 m
Cutting line diameter: ................................. 2 mm
Tank capacity ................................................0.8 l
Spark plug ............................... Champion RCJ6Y
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN ISO 11806-1; EN ISO 22868;
EN ISO 22867.
L
pA
sound pressure level ..................... 93.2 dB(A)
K
pA
uncertainty ..........................................1.5 dB
L
WA
sound power level ........................ 110 dB(A)
K
WA
uncertainty ..........................................1,5 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Functions
Vibration emission value a
h
= 7 m/s
2
K uncertainty = 1.5 m/s
2
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Assembly
5.1.1 Fitting the steady grip
Install the steady grip as shown in Figures 3a-3c.
Do not tighten the screws until you have set the
perfect working position with the carrying strap.
The steady grip should be aligned as shown in
Figure 1. To dismantle, proceed in reverse order.
5.1.2 Fitting the long handle (Fig. 4a-4c)
Pass the handle screw (32) through the washer
(34) and into the connecting piece of the long
handle (1) (Fig. 4b). Secure the handle screw loo-
sely with the nut (33).
Now press the locking lever (A) and push the long
handle (Fig. 4a/Item 2) carefully into the connec-
ting piece for the long handle. While doing so,
ensure that the drive shafts on the inside of the
long handle slide into each other (turn the spool
head gently, if required). The lug of the locking
lever (A) must latch into the hole (B). Now tighten
the handle screw as shown in Figure 4c. After this
initial assembly, you will only have to loosen the
handle screw and activate the lever to dismantle
the long handle.
5.1.3 Fitting the blade guard hood
Important: The cutting blade guard hood must be
fi tted if you wish to work with the cutting blade.
The guard hood for the cutting blade must be ins-
talled as shown in Figures 5a – 5c.
5.1.4 Fitting/Replacing the cutting blade
The fi tting of the cutting blade is shown in Figures
6a – 6g. To dismantle, proceed in reverse order.
•
Fit the carrier plate (22) onto the spline shaft
(Fig. 6b)
•
Securely fit the cutting blade (18) on the co-
ver ring (Fig. 6c)
•
Place the pressure plate (23) over the thread
of the spline shaft (Fig. 6d).
•
Plug on the cover of the pressure plate (24)
(Fig. 6e).
•
Look for the hole in the carrier plate, line up
with the notch underneath, lock with the sup-
plied Allen key (29), and tighten the nut (25)
(Fig. 6f/6g). Important: Left-hand thread
Anl_GH_BC_30_AS_SPK7.indb 21Anl_GH_BC_30_AS_SPK7.indb 21 16.06.14 11:4216.06.14 11:42
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell GH-BC 30 AS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GH-BC 30 AS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info