Manual Einhell GH-BC 25 AS (page 24 of 88) (English, Danish, Swedish, Norwegian)

605957

Zoom out

Zoom in

1/88

- 24 -

Important: The cutting tool starts to operate

when the engine is started.

8. After approx. 5-10 seconds actuate the thrott-

le lever brieﬂ y. This will release the choke le-

ver and the engine will return to idling speed.

9. If the engine does not start up, repeat steps

4-8 above.

Please note: If the engine does not start up even

after several attempts, read the section “Engine

Troubleshooting”. Please note: Always pull the

starter cord out in a straight line. If it is pulled out

at an angle, then friction will occur on the eyelet.

As a result of this friction, the cable will become

frayed and will wear away faster. Always hold the

starter handle when the cable retracts. Never

allow the cable to snap back when it has been

pulled out.

7.2 Starting the engine when warm

(The equipment has been idle for less than 15-20

min.)

1. Set the equipment down on a hard, level sur-

face.

2. Switch the ON/OFF switch to “I”.

3. Hold the equipment ﬁ rmly and pull out the

starter cable until you feel it start to resist.

Then tug sharply on the starter cable. The

equipment should start after 1-2 tugs. If the

equipment does not start after 6 pulls, repeat

steps 1 – 7 of the procedure for starting the

engine from cold.

7.3 Switching oﬀ the engine

Emergency Stop procedure:

If it becomes necessary to stop the equipment im-

mediately, set the ON/OFF switch to “Stop” or “0”

Normal procedure:

Let go of the throttle lever and wait until the engi-

ne has changed to idling speed. Then set the ON/

OFF switch to “Stop” or “0”.

7.4 Practical tips

Practice all operating techniques with the engine

switched oﬀ before you start to use the equip-

ment.

8. Working with the petrol power

scythe

Extending the cutting line

Caution! Do not use any kind of metal wire or

metal wire encased in plastic in the line spool.

This may cause serious injuries to the user.

To extend the cutting line, run the engine at full

speed and tap the line spool on the ground. This

will automatically extend the line. The blade on

the safety shield will cut the line to the appropriate

length (Fig. 26).

Important: Remove all grass and weed remnants

at regular intervals to prevent the shaft tube over-

heating. Lawn, grass and weed remnants become

trapped under the safety shield (Fig. 27) and

prevent the shaft tube from receiving adequate

ventilation. Remove the remnants carefully using

a screwdriver or the like.

Diﬀ erent cutting methods

When the equipment is correctly assembled it

will cut weeds and long grass in places which are

diﬃ cult to access, e.g. along fences, walls and

foundations and also around trees. It can also

be used for „mowing“ down vegetation so that a

garden can be better prepared or a certain area

cleared down to the soil.

Please note: Even if it is used carefully, cutting

around foundations, stone or concrete walls, etc.

will result in the line suﬀ ering more than normal

wear.

Trimming/mowing

Swing the trimmer from side to side in a scything

motion. Always keep the line spool parallel to the

ground. Check the site and decide which cutting

height you require. Guide and hold the line spool

at the required height to obtain an even cut (Fig.

28).

Low trimming

Hold the trimmer right in front of you at a slight

angle so that the underside of the line spool is

above the ground and the line strikes the correct

target. Always cut away from yourself. Never draw

the trimmer towards yourself.

Anl_GH_BC_25_AS_SPK1.indb 24Anl_GH_BC_25_AS_SPK1.indb 24 19.03.15 11:1119.03.15 11:11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GH-BC 25 AS in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 3,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell GH-BC 25 AS

Einhell GH-BC 25 AS User Manual - German, Dutch, French, Portuguese, Spanish - 68 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GH-BC 25 AS Manual

Product: