Manual Einhell GH-BC 25 AS (page 23 of 88) (English, Danish, Swedish, Norwegian)

605957

Zoom out

Zoom in

1/88

- 23 -

5.1.5 Fitting the cutting line guard hood to

the blade guard hood

Important: The cutting line guard hood must be

additionally ﬁ tted if you want to work with the cut-

ting line.

The guard hood for the cutting line must be ins-

talled as shown in Figures 7a – 7b.

6.1.6 Fitting/Replacing the line spool

The ﬁ tting of the line spool is shown on Figure 7c.

To dismantle, proceed in reverse order.

Look for the hole in the carrier plate, line up with

the notch beneath it, lock with the supplied Allen

key (29), and screw the line spool onto the thread.

Important: Left-hand thread

5.2 Setting the cutting height

•

Fit the carrying strap as shown in Figures 8a-

8c.

•

Hook the equipment to the carrying belt (Fig.

8d).

•

Adjust the perfect working and cutting posi-

tion using the various strap adjusters on the

carrying strap (Fig. 8e).

•

In order to establish the optimum length of

the carrying strap, you should then make a

few swinging movements without starting the

engine (Fig. 9a).

The carrying strap is ﬁ tted with a quick-release

mechanism. Pull the red strap section (Fig. 8f) if

you need to remove the strap quickly.

Important: Always use the strap when working

with the equipment. Attach the strap as soon as

you have started the engine and it is running in

idle mode. Switch oﬀ the engine before you take

oﬀ the carrying strap.

6. Before starting the equipment

Check the equipment for the following each time

before use:

•

That there are no leaks in the fuel system.

•

That the equipment is in perfect condition and

that the safety devices and cutting devices

are complete.

•

That all screws are securely fastened.

•

That all moving parts move smoothly.

6.1 Fuel and oil

Recommended fuels

Use only a mixture of unleaded petrol and special

2-stroke engine oil. Mix the fuel mixture as indica-

ted on the fuel mixing table.

Important: Do not use a fuel mixture which has

been stored for longer than 90 days.

Important: Never use 2-stroke oil with a recom-

mended mixing ratio of 100:1. The manufacturer’s

warranty will be voided in case of engine damage

due to inadequate lubrication.

Important: Only use containers designed and ap-

proved for the purpose to transport and store fuel.

Pour the correct quantities of petrol and 2-stroke

oil into the mixing bottle (see scale printed on the

bottle). Then shake the bottle well.

6.2 Fuel mixture table

Mixing procedure: 40 parts petrol to 1 part oil

Petrol 2-stroke oil

1 liter 25 ml

5 liters 125 ml

7. Operation

Please note that the statutory regulations gover-

ning noise abatement may diﬀ er from town to

town.

Before starting up the equipment remove the pro-

tective caps from the cutting blade (15).

7.1 Starting the engine when cold

Fill the tank with the required amount of oil/petrol

mix. See “Fuel and oil”.

1. Set the equipment down on a hard, level sur-

face.

2. Press the fuel pump (primer) (Fig. 1/Item 7)

10 times.

3. Move the ON/OFF switch (Fig. 1/Item 9) to “I”

4. Set the choke lever (Fig. 1/Item 5) to „ “.

5. Hold the equipment ﬁ rmly and pull out the

starter cable (Fig. 1/Item 4) until you feel it

start to resist. Then tug sharply on the starter

cable 2 times.

6. Set the choke lever (Fig. 1/Item 5) to „

“.

7. Hold the equipment ﬁ rmly and pull out the

starter cable (Fig. 1/Item 4) until you feel it

start to resist. Then tug sharply on the starter

cable 4 times. The equipment should start.

Important: Never allow the starter cable to

snap back. This may damage the equipment.

Anl_GH_BC_25_AS_SPK1.indb 23Anl_GH_BC_25_AS_SPK1.indb 23 19.03.15 11:1119.03.15 11:11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GH-BC 25 AS in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 3,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell GH-BC 25 AS

Einhell GH-BC 25 AS User Manual - German, Dutch, French, Portuguese, Spanish - 68 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GH-BC 25 AS Manual

Product: