605766
22
Zoom out
Zoom in
Previous page
1/88
Next page
GB
- 22 -
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a quali ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a quali ed electrician.
8.3 Maintenance
A worn out or damaged cutting unit should be
replaced by an authorised expert (see adress
on the warranty certificate).
Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you
can work safely with the scarifier.
Store the scarifier in a dry place.
For longer life, all screw-fastened parts, such
as wheels and axles should be cleaned and
subsequently oiled.
Regular servicing of the scarifier not only
secures longer endurance and performance,
but also contributes to an accurate and simp-
le scarification of your lawn.
At the end of the season, carry out a general
check of the scarifier, and remove all residue
collected. Before the start of every season, it
is absolutely necessary to check the state of
the scarifier. Contact our Customer Service
(see address on the warranty certificate) if
repair work is necessary.
8.4 Changing the roller (see Figures 16-19)
Be sure to wear work gloves!
Only replace the roller with a genuine Einhell rol-
ler, as this will ensure top performance and safety
under all conditions.
Remove the two Allen screws (Fig. 16 / Item A).
Lift the roller on this side and pull out in the direc-
tion of the arrow (Fig. 17).
Now slide the new roller in the direction of the ar-
row (Fig. 19) onto the square-ended drive (Fig. 18
/ Item B) and press into the holder (Fig. 19).
Refasten the roller with the two Allen screws (Fig.
16 / Item A).
Apply grease to the square-ended drive from time
to time so that the rollers can be changed easily.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Replacement cutting unit Art. No.: 34.055.80
Replacement aerating unit, Art. No.: 34.055.70
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o ces.
Anl_GC_SA_1231_SPK1.indb 22Anl_GC_SA_1231_SPK1.indb 22 19.08.14 15:1919.08.14 15:19
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell GC-SA 1231 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GC-SA 1231 in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell GC-SA 1231

Einhell GC-SA 1231 User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info