605766
21
Zoom out
Zoom in
Previous page
1/88
Next page
GB
- 21 -
checking them. Completely unwind the power
cable. Also check power cable entry points, plugs
and socket couplers for kinks.
6. Operation
Connect the machine’s power supply cable to the
plug (Fig. 14/Item 1) and secure the power cable
with the stress-relief clip (Fig 14/Item 2).
To prevent accidental start-up of the equipment,
the push-bar (Fig. 15 / Item 5) is equipped with
a safety lock-o (Fig. 15 / Item 2) which must be
pressed before the lever switch (Fig. 15 / Item 1)
can be pressed. If the lever switch is released, the
equipment switches o .
Repeat this process several times so that you are
sure that the machine functions properly. Before
you perform any repair or maintenance work on
the machine, ensure that the cutting unit is not ro-
tating and that the power supply is disconnected.
Important! Never open the ejector ap when the
motor is running. A rotating cutting unit can cause
injuries.
Always fasten the ejector ap carefully. The ap
ips back to the “Closed” position by the tension
springs!
Always ensure that a safe distance (provided
by the long handles) is maintained between the
user and the housing. Be especially careful when
scarifying and changing direction on slopes and
inclines. Maintain a solid footing and wear sturdy,
non-slip footwear and long trousers. Always sca-
rify along the incline (not up and down).
For safety reasons, the scari er may not be used
to scarify inclines whose gradient exceeds 15
degrees.
Use special caution when backing up and pulling
the scari er (tripping hazard)!
Tips for proper working
It is recommended that you overlap scarifying
paths a little.
Try to scarify in straight lines for a nice, clean look.
Insodoing, the aeration swaths should always
overlap each other by a few centimeters in order
to avoid bare strips.
As soon as grass clippings start to trail the scari-
er, it is time to empty the grass basket.
Danger! Before taking o the grass basket,
switch o the motor and wait until the roller
has come to a stop.
To remove the grass basket, lift up the ejector ap
with one hand, while unhooking the basket with
the other.
How frequently you should scarify your lawn is
determined primarily by the speed at which the
grass grows and the hardness of the soil.
Keep the underside of the equipment clean and
remove soil and grass build-up. Deposits make it
more di cult to start the aerator and decrease the
quality of the scarifying.
Always scarify along inclines (not up and down).
Switch o the motor before doing any checks on
the roller.
Danger!
The roller rotates for a few seconds after the
motor is switched o . Never attempt to stop the
roller. In the event that the rotating roller strikes
an object, immediately switch o the equipment
and wait for the roller to come to a complete stop.
Then inspect the condition of the roller. Replace
any parts that are damaged (see section 8.4).
Lay the power cable on the ground in loops in
front of the power outlet. Scarify away from the
power outlet and cable, making sure that the
power cable always trails in the already scari ed
grass so that the equipment does not travel over
the cable.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Anl_GC_SA_1231_SPK1.indb 21Anl_GC_SA_1231_SPK1.indb 21 19.08.14 15:1919.08.14 15:19
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell GC-SA 1231 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GC-SA 1231 in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell GC-SA 1231

Einhell GC-SA 1231 User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info