Manual Einhell GC-PM 46-2 S HW (page 24 of 124) (English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Norwegian)

605750

Zoom out

Zoom in

1/124

- 24 -

Danger: The blade begins to rotate as soon as

the engine is started.

6.1 Starting the engine

1. Ensure that the ignition cable is connected to

the spark plug.

2. Press the fuel pump (primer) (Fig. 6/Item 2)

three times. You can skip this point if the engi-

ne has already warmed up.

3. Stand behind the lawn mower. Actuate the

engine start/stop lever (Fig. 5b) with one

hand. The other hand must be on the starter

handle.

4. Start the engine using the reversing starter

(Fig. 1/Item 9). To do this pull out the handle

approx. 10 –15 cm (until you feel a resistance)

and then start the engine with a sharp tug.

If the engine does not start, tug the handle

again.

Note! Never allow the actuator cable to snap

back.

Note! In cold weather, it may be necessary to

repeat the starting process several times.

Drive unit

Drive lever/clutch lever (Fig. 5a/Item 1b):

If you press this (Fig. 5c) the clutch for the drive

will be closed and the lawnmower will start to

move with the engine running. Release the drive

lever in good time to stop the moving lawnmower.

Practice starting and stopping before you use the

mower for the ﬁ rst time until you are familiar with

controlling the mower.

6.2 Tips on mowing properly

Danger!

Never open the chute ﬂ ap when the grass

bag has been detached (to be emptied) and

the engine is still running. The rotating blade

can cause serious injuries!

Always carefully fasten the chute ﬂ ap and

debris bag. Switch oﬀ the engine before you

remove them.

Whenever you need to perform any kind of

adjustment, maintenance or repair work,

switch oﬀ the engine and wait until the blade

no longer rotates. Pull oﬀ the spark plug con-

nector.

Mowing

The engine is conﬁ gured for an optimal grass cut-

ting speed, for ejecting grass into the debris bag,

and for many years of use.

Only use a sharp blade that is in good condition.

This will prevent the grass blades from fraying

and the lawn from turning yellow.

Try to mow in straight lines for a nice, clean look.

The swaths should overlap each other by a few

centimeters in order to avoid stripes.

Keep the underside of the mower housing clean

and remove grass build-up. Deposits not only

make it more diﬃ cult to start the mower; they

decrease the quality of the cut and make it harder

for the equipment to bag the grass.

Always mow along inclines (not up and down).

You can prevent the lawn mower from slipping

down by holding a position at an angle upwards.

Select the cutting height according to the length

of the grass. If necessary, mow a number of times

so that you never cut more than 4cm of grass in

one go.

Switch oﬀ the engine before doing any checks on

the blade. Keep in mind that the blade continues

to rotate for a few seconds after the engine has

been switched oﬀ . Never attempt to manually

stop the blade. Regularly check to see if the

blade is securely attached, is in good condition

and is sharp. If the contrary is the case, sharpen

the blade or replace it. In the event that the blade

strikes an object, immediately switch oﬀ the lawn

mower and wait for the blade to come to a com-

plete stop. Then inspect the condition of the blade

and the blade mount. Replace any parts that are

damaged.

Mulching (Fig. 4b)

In mulching mode the cuttings are shredded in

the enclosed mower housing and then spread

back onto the lawn. It is not necessary to gather

and dispose of the grass.

Mulching is only possible if the lawn is relatively

short. Optimum results can be achieved only with

a mulching blade (available as an accessory).

To use the mulching function, disconnect the deb-

ris bag, slide the mulching adaptor into the ejector

opening (Item 4b) and close the ejector opening.

Anl_GC_PM_46_2_S_HW_SPK7.indb 24Anl_GC_PM_46_2_S_HW_SPK7.indb 24 08.10.14 09:4308.10.14 09:43

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GC-PM 46-2 S HW in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Norwegian as an attachment in your email.

The manual is 3,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GC-PM 46-2 S HW Manual

Product: