605958

Einhell GC-ET 4526 Manual

20
Zoom out
Zoom in
Previous page
1/120
Next page
GBGB
- 20 -
Using the grass trimmer as an edge trimmer
(Fig. 11)
To cut the edges of lawns and ower beds, the
grass trimmer can be converted as follows:
•
Pull the lock in the direction of the arrow (Fig.
11/Item 10).
•
With the lock pulled, turn the motor head
through 90°. (It can be turned 90° to the left
and to the right.)
•
The height adjustment works as described in
section 5.3.
•
Now you have converted the grass trimmer to
an edge trimmer for cutting the lawn vertically.
7. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
•
Use a brush to remove deposits from the
safety guard.
8.2 Replacing the line spool
Important! Make sure that you pull out the
power plug before replacing the line spool!
•
Press the sides of the spool cover as shown
and remove the cover (Figure 12b).
•
Remove the empty line spool.
•
There is a spare line spool in the additional
handle. To take it out, proceed as follows:
Press the lever (Fig. 12a/Item B) in the direc-
tion of the arrow and pull the spare line spool
out of the holder.
•
Thread the end of the line from the new line
spool through the eyelet in the spool mount
(Fig. 12c) and allow approx. 10 cm of line to
project.
•
Fit the spool cover back in the spool mount.
•
When you start the equipment again the line
will be cut to the perfect length automatically.
Important! Bits of the nylon line could cause
injury when ung out!
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Spare line spool Art. no.: 34.056.90
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council oces.
Anl_GC_ET_4025_4526_SPK7.indb 20 18.12.13 11:40
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell GC-ET 4526 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GC-ET 4526 in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 4,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info