644131

Efco 156 Manual

36
Zoom out
Zoom in
Previous page
1/60
Next page
36
72 73 74 75
Italiano English Français
MANUTENZIONE MAINTENANCE ENTRETIEN
FILTRO ARIA - Svitare le viti (A, Fig. 72) e controllare giornalmente il
filtro aria (B). Pulire con sgrassante Emak cod. 001101009, lavare
con acqua e soffiare a distanza con aria compressa dall'interno
verso l'esterno. Sostituire il filtro se è fortemente intasato o
danneggiato.
ATTENZIONE! - Quando si rimonta il filtro (B), incastrarlo bene
nel suo alloggiamento nel coperchio.
FILTRO CARBURANTE - Verificare periodicamente le condizioni del
filtro carburante. In caso di sporcizia eccessiva, sostituirlo (Fig. 73).
POMPA OLIO (automatica regolabile) - La portata è preregolata
di fabbrica. L’erogazione dell’olio può essere variata dall’operatore,
a seconda delle esigenze, tramite l’apposita vite di registro (Fig. 74).
La portata dell’olio avviene solo con la catena in movimento.
ATTENZIONE - Non utilizzare mai olio di recupero.
GRUPPO AVVIAMENTO - Tenere libere e pulite le feritoie di
raffreddamento del carter gruppo avviamento (Fig. 75) con
pennello o aria compressa.
MOTORE / VALVOLA DI DECOMPRESSIONE - Pulire
periodicamente le alette del cilindro con pennello o aria compressa
(Fig. 76). L’accumulo di impurità sul cilindro può provocare
surriscaldamenti dannosi per il funzionamento del motore.
Controllare e pulire eventuali impurità alla base della valvola di
decompressione; potrebbe rimanere aperta.
CANDELA - Periodicamente si raccomanda la pulizia della candela
e il controllo della distanza degli elettrodi (Fig. 77).
Utilizzare candela NGK BPMR6A o di altra marca di grado termico
equivalente.
FRENO CATENA - Nel caso il freno catena non funzioni
correttamente, smontare il carter copricatena e pulire a fondo i
componenti del freno. Quando il nastro del freno catena è usurato
e/o deformato, sostituirlo (A, Fig. 78).
Verificare e sostituire se necessario, l’arresto di sicurezza della
catena (B, Fig. 78).
BARRA - Ruotare la barra e verificare che i fori di lubrificazione
siano liberi da impurità (Fig. 79).
AIR FILTER - Losen screws A (Fig. 72) and check the air filter (B) each
day. Clean with Emak degreaser p/n 001101009, rinse with water
and blast dry with compressed air, not too close, blowing from the
inside outwards. Renew the filter if heavily clogged or damaged.
WARNING! – When refitting the air filter (B), fit it into the
cover well, before reassembly.
FUEL FILTER - Check the fuel filter periodically. Replace it if too
dirty (Fig. 73).
OIL PUMP (automatic/adjustable) - Flow adjustment is pre-set by
the manufacturer. Oil flow can be adjusted by the operator
according to specific requirements by means of the special
adjusting screw (Fig. 74). Oil flow occurs only when the chain is
moving.
WARNING - Never use scavenge oil.
STARTING UNIT - Use a brush or compressed air to keep the
cooling louvers of the starter assembly free and clean (Fig. 75).
ENGINE / DECOMPRESSION VALVE - Clean the cylinder fins
(Fig. 76) with compressed air or a brush periodically. Dangerous
overheating of engine may occur due to impurities on the cylinder.
Check the base of the decompression valve; clean away any
residues, which could cause the valve to stay open.
SPARK PLUG - Clean the spark plug and check the electrode gap
periodically (Fig. 77).
Use NGK BPMR6A or of other brand with the same thermal grade.
CHAIN BRAKE - If the chain brake does not work properly, remove
the chain cover and the clean brake components. Replace the chain
brake band if worn or deformed (A, Fig. 78).
Check and, if necessary, replace the chain safety stop (B, Fig. 78).
GUIDE BAR - Turn the guide bar and check that the lubrication
holes are free from impurities (Fig. 79).
FILTRE A AIR - Dévissez les vis A (Fig. 72) et contrôlez tous les jours
le filtre à air (B). Nettoyer avec du dégraissant Emak cod. 001101009,
laver avec de l'eau et souffler à distance avec de l'air comprimé de
l'intérieur vers l'extérieur. Remplacer le filtre s'il est fortement
colmaté ou endommagé.
ATTENTION! - Lors du remontage du filtre (B), s’assurer de le
faire entrer parfaitement dans son logement du couvercle.
FILTRE CARBURANT - Vérifiez périodiquement les conditions du
filtre carburant; s’il est trop sale, mieux vaut le changer. (Fig.73).
POMPE A HUILE (automatique réglable) - Le débit est préréglé à
l’usine. L’opérateur peut varier la distribution de l’huile selon les
exigences, au moyen de la vis de réglage (Fig.74). Il n’y a débit
d’huile que lorsque la chaîne est en mouvement.
ATTENTION - N’utilisez jamais d’huile de récupération.
GROUPE DEMARREUR - Veillez à ce que les fentes de
refroidissement du carter du groupe démarreur soient toujours
dégagées (Fig.75). Utilisez un pinceau ou de l’air comprimé.
MOTEUR / VALVE DE DÉCOMPRESSION - Nettoyez régulièrement
les ailettes du cylindre à l’aide d’un pinceau ou d’air comprimé
(Fig. 76). L’accumulation d’impuretés sur le cylindre peut provoquer
des surchauffes nuisibles au bon fonctionnement du moteur.
Contrôler et nettoyer les impuretés éventuelles qui se seraient
déposées à la base de la valve de décompression; celle-ci pourrait
rester ouverte.
BOUGIE - Il est recommandé de nettoyer périodiquement la
bougie et de contrôler la distance entre les électrodes (Fig.77).
Utiliser une bougie NGK BPMR6A ou autre marque avec degré
thermique équivalent.
FREIN DE CHAINE - Si le frein de chaîne ne fonctionne pas bien,
démontez le carter protège-chaîne et nettoyez à fond les éléments
du frein. Lorsque le ruban du frein de chaîne est usé et/ou déformé,
remplacez-le (A, Fig.78).
Vérifiez et, si cela s’avère nécessaire, remplacez l’arrêt de sûreté de
la chaîne (B, Fig.78)
GUIDE - Tournez le guide et vérifiez que les trous de lubrification
sont dégagés d’éventuelles impuretés (Fig.79).
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco 156 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco 156 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info